495124
17
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
en
17
Timer programming
Timer programming *
* depending on model
You can delay the start of the programme
by 3, 6 or 9 hours.
–Switch on ON/OFF switch (.
Keep pressing the Preselected starting
time button 0 until the appropriate
display 3h, 6h or 9h is lit.
Press START button h, timer
programming is activated.
To delete the preselected starting time,
keep pressing the Preselected starting
time button 0 until none of the
displays 3h, 6h or 9h is lit.
You can change your programme
selection at any time until the
programme starts.
End of programme
The programme has ended when neither
of the two displays ` or X is lit.
The end of the programme is also
indicated by an acoustic signal.
The buzzer volume can be set in 4 stages.
Accordingly 0, 1, 2 or 3 displays are lit
(see water hardness table). Factory
setting: 2. This function can be changed
as follows:
Open the door.
–Switchon ON/OFF switch(.
Hold down button > P and press
START button h until the dry
display ` and salt refill indicator )*
flash.
Release buttons.
Keep pressing button > P until
the salt refill indicator )* and rinse
aid refill indicator )" flash.
Release buttons.
The refill indicators )* and )" flash
and the displays # and + are lit
(= Setting 2). The set buzzer volume
can be heard.
To change the setting:
Press the button < H until
the required setting has been selected.
Press START button h.
Thedisplays go out. Theselected
setting is saved.
Close the door.
Note
To save energy, the dishwasher
automatically switches off after the end
of the programme.
Interrupting the programme
Open the door.
Switch off ON/OFF switch (.
The LEDs go out. The programme is
saved.
If the door was opened on an
appliance which has a warm water
connection or is heated, first leave the
door ajar for several minutes and then
close. Otherwise, expansion (pressure)
may cause the appliance door to
spring open or water to run out of the
appliance.
To continue the programme, switch on
the ON/OFF switch ( again.
Close the door.
Terminati ng theprogramme
Terminating the programme
(Reset)
Open the door.
Press START button h for
approx. 3 sec. until all displays go out.
Close the door.
The remaining programme sequence
for draining the residual water takes
approx. 1 minute.
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

balay-3vf301np

Suche zurücksetzen

  • Für diese Maschine 3VF301NP von Balay habe ich keine Bedienugsanleitung. Die Maschine pumpt zum Schluss nicht ab, das Wasser bleibt im Bodenbereich stehen. Wenn ich die Maschine erneut anstelle pumpt sie schubweise das Wasser ab. Es blinkt immer das Symbol (Bürste).
    Was kann bzw. muss ich tun und wie komme ich an eine deutsche Anleitung?

    Vielen Dank für Ihre Hilfe

    MfG Uli Eingereicht am 17-9-2019 09:59

    Antworten Frage melden
  • Maschine verbraucht kein Salz, ist aber eine 3VF304NA, Gläser milchig Eingereicht am 26-5-2017 14:00

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Balay 3VF301NP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info