Bedienungsanleitung Balboa SpaTouch2 (Seite 11 von 28) (Englisch)

784763

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Manufactured under one or more of these patents.

U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2, Canadian Patent: 2342614,

Australian patent: 2373248 other patents both foreign and domesc applied for and pending. All material copyright of Balboa Water Group.

42281_A | Compable with SpaTouch 1 & 2 11 03.17

The Settings Screen

Heat Mode

Ready vs. Rest | Circulaon Mode | Ready-in-Rest Mode

In order for the spa to heat, a pump needs to circulate

water through the heater. The pump that performs

this function is known as the “heater pump.”

The heater pump can be either a 2-speed pump

(Pump 1) or a circulation pump.

If the heater pump is a 2-Speed Pump 1, Ready Mode

will circulate water every 1/2 hour, using Pump 1 Low,

in order to maintain a constant water temperature,

heat as needed, and refresh the temperature display.

This is known as “polling.”

Rest Mode will only allow heating during programmed

filter cycles. Since polling does not occur, the temper-

ature display may not show a current temperature

until the heater pump has been running for a minute

or two.

When the heater pump has come on automatically

(for example for heating) you can switch between low

speed and high speed but you cannot turn the heater

pump off.

Circulation Mode

If the spa is configured for 24HR circulation, the

heater pump generally runs continuously. Since the

heater pump is always running, the spa will maintain

set temperature and heat as needed in Ready Mode,

without polling.

In Rest Mode, the spa will only heat to set temper-

ature during programmed filter times, even though

the water is being filtered constantly when in 24HR

circulation mode.

Heat Mode – Ready vs. Rest

Ready in Rest Mode appears in the display if the spa is

in Rest Mode and the Jets 1 Button is pressed. When

the heater pump has come on automatically (for ex-

ample for heating) you can switch between low speed

and high speed but you cannot turn the heater pump

off. After 1 hour, the System will revert to Rest Mode.

This mode can also be reset by selecting the Heat

Mode line on the Screen shown here.

Fill it up!

Preparation & Filling

Fill the spa to its correct operating level. Be sure

to open all valves and jets in the plumbing system

before filling to allow as much air as possible to

escape from the plumbing and the control system

during the filling process.

After turning the power on at the main power

panel, the top-side panel will display a splash screen

or startup screen.

Priming Mode – M019*

After the initial start-up sequence, the control will

enter Priming Mode and display a Priming Mode

screen. Only pump icons appear on the priming

mode screen. During the priming mode, the heater is

disabled to allow the priming process to be complet-

ed without the possibility of energizing the heater

under low-flow or no-flow conditions. Nothing comes

on automatically, but the pump(s) can be energized

by selecting the “Jet” buttons. If the spa has a Circ

Pump, it can be turned on and off by pressing the

“Circ” button during Priming Mode.

Ready-in-Rest Mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Balboa SpaTouch2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info