Bedienungsanleitung Balboa SpaTouch2 (Seite 22 von 28) (Englisch)

784763

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Manufactured under one or more of these patents.

U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2, Canadian Patent: 2342614,

Australian patent: 2373248 other patents both foreign and domesc applied for and pending. All material copyright of Balboa Water Group.

42281_A | Compable with SpaTouch 1 & 2 22 03.17

Utilities

GFCI Test Feature

CE Product

Reset Button:

Forcing the GFCI Trip Test

(North America Only)

Warning:

The Ground Fault Circuit Interrupter (GFCI) or Residual

Current Detector(RCD) is an important safety device and is

required equipment on a hot tub installation.

(The GFCI Test Feature is not available on CE rated systems).

Used for verifying a proper installaon

Your spa may be equipped with a GFCI Protection feature. If

your spa has this feature enabled by the manufacturer, the

GFCI Trip Test must occur to allow proper spa function.

On some systems:

On those systems that automatically test the GFCI within 1 to

7 days after startup:

The end-user must be trained to expect this one-time test

to occur. The end-user must be trained how to properly

reset the GFCI. If freezing conditions exist, the GFCI or RCD

should be reset immediately or spa damage could result.

CE registered systems do not have an RCD Test Feature due

to the nature of the electrical service. Some UL registered

systems do not have the GFCI Test Feature activated. The

end-user must be trained how to properly test and reset

the RCD.

Only use the Reset Button prior to moving the spa to a new

location. Pressing the Reset the button forces a new Test to

be performed at the new location.

The installer can cause the GFCI Trip Test to occur sooner by

pressing Test on the GFCI Test screen.

The GFCI should trip within several seconds and the spa

should shut down. If it does not, shut down the power and

manually verify that a GFCI breaker is installed and that the

circuit and spa are wired correctly. Verify the function of

the GFCI with its own test button. Restore power to the spa

and repeat the GFCI Trip Test.

Once the GFCI is tripped by the test, reset the GFCI and the

spa will operate normally from that point. You can verify a

successful test by navigating to the above screen. “Passed”

should appear after the Reset line is selected on the GFCI

screen.

Within 1 to 7 days after startup, the spa will trip the GFCI to

test it. (The number of days is factory programmed.) The GFCI

must be reset once it has tripped. After passing the GFCI Trip

Test, any subsequent GFCI trips will indicate a ground fault or

other unsafe condition and the power to the spa must be shut

off until a service person can correct the problem.

Touching the GFCI Test Icon on the Utilities Screen takes

you to the GFCI Test screen..

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Balboa SpaTouch2 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info