Bedienungsanleitung BandG Zeus2 Glass Helm (Seite 24 von 52) (Englisch)

658689

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

22 |

Software setup | Zeus Glass Helm Installation Manual

Diagnostics

The NMEA 2000 tab on the diagnostics page can provide information useful for identifying an

issue with the network.

Bus state: This simply indicates whether the bus is powered, but not necessarily connected

to any data sources. However if bus shows as ‘o ’, but power is present along with an

increasing error count, it is possible that termination or cable topology is incorrect.

Rx Over ows: The CAN driver got too many messages for its bu er before the application

could read them.

Rx Overruns: The CAN hardware got too many messages for its bu er before the CAN driver

could read them.

Rx/Tx Errors: These two numbers increase when there are error messages, and decrease

when messages are received successfully. These (unlike the other values) are not a cumulative

count. Under normal operation these should be at 0. Values around 96 upwards indicate

a heavily error prone network. If these numbers go too high for a given device, it will

automatically drop o the bus.

Fast Packet Errors: Cumulative counter of any fast packet error. This could be missed frame,

or frame out of sequence etc. NMEA 2000 PGNs are made of up to 32 frames. The entire

message will be discarded when a frame is missed.

 Note: The above information may not always indicate an issue that can be simply resolved

with minor adjustment to network topology or connected devices and their activity on the

network. However Rx and Tx errors are most likely indicating issues with the physical network,

which may be resolved by correcting termination, reducing backbone or drop lengths, or

reducing the number of network nodes (devices).

Damping

If data appears erratic or too sensitive, damping may be applied to make the information

appear more stable. With damping set at MIN, the data is presented in raw form with no

damping applied. This is available for heading, course over ground, speed over ground,

apparent wind, true wind, boat speed, depth, and tide sourced from NMEA 2000.

Calibration

An o set (positive or negative) can be applied to correct inaccuracies in boat speed, sea

temp, air temp, barometric pressure, and depth sourced from NMEA 2000.

External alarm setup

The Siren Enabled option must be set in order for the unit to drive the buzzer when an

alarm condition arises. Its setting also determines the operation of the external alarm output

(blue wire).

Echosounder setup

Select echosounder source

If only one sonar source is present in the network, selection is not required as it should be

picked up automatically. However when more than one source exists (eg a BSM-2 or other

display with internal sonar), select the desired source in the Echo Settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BandG Zeus2 Glass Helm Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BandG Zeus2 Glass Helm

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info