Bedienungsanleitung BandG ZM Series Monitors (Seite 7 von 26) (Englisch)

658677

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Display installation | ZM Series User Manual

Display installation

It is recommended that the unit be powered and connected to a video source to assist in

selecting a suitable mounting location, prior to irreversible modication of the vessel’s helm

station. When planning the display location, the following points should be considered to

ensure safe, comfortable and reliable operation:

• Convenience - the mounting location should be easily accessible to allow operation of the

controls and should enable easy viewing of the display.

• Viewing angle - the viewing angle inuence the viewability of the monitor. The

recommended viewing angles relative to perpendicular are shown in the illustrations below.

Horizontal viewing angles

A: Optimum viewing angle

B: Good viewing angle

C: Poor viewing angle or obstructed view

• Access - there must be sucient space behind the display to allow cable connections to the

rear connectors, avoiding tight bends in the cable. Also ensure there is sucient access for

tightening wing nuts/screws on the mounting brackets, where used.

• Interference - the selected location should be far enough away from devices that may

cause interference, such as motors, generators and radio transmitters/receivers.

• Magnetic compass - mount the display at least 1 metre (3 ft.) away from a magnetic

compass.

• Environment - to prevent overheating, do not restrict airow at the rear of the display unit;

ensure that there is adequate ventilation, particularly if the display unit is pod-mounted. If

the space behind the display is air conditioned or cooled by a fan, it will help in keeping the

unit’s temperature down. The ZM16/19 displays are designed to operate in indoor/outdoor

environments and in high ambient brightness conditions, however, we recommended

the display not be mounted in a location where it will be exposed to direct sunlight for

prolonged periods. The display should be protected from physical damage and excessive

vibration. Although the display unit is waterproof from the front when installed correctly, it is

good practice to mount it in a protected area away from prolonged and direct exposure to

rain and salt spray.

Warning: Damage incurred to monitor through failure to provide adequate ventilation

could invalidate your warranty. Do not recess device in to an enclosure shared with a heat

source. e.g. engine compartment.

Cutout template

Use the supplied scale template to help mark up the cutout area.

¼ Note: Always check the template dimensions against the physical monitor to ensure

dimensions are correct, prior to making the cutout.

Fixing options

The ZM series monitors can be dash or bracket mounted (using optional VESA adaptor).

When dash mounting, unit should be tted using the rear mounted dash mount brackets,

and bezel screws from the front. Exclusion of the dash mount bracket will greatly increase

strain on bezel screws and adjacent bezel plastics, and is not recommended.

C C

A A

40°

70°

20°

80° 80°

80°

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BandG ZM Series Monitors Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von BandG ZM Series Monitors

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info