Bedienungsanleitung Bang Olufsen BEOLAB 19 (Seite 8 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

637724

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

English

Set up your BeoLab 19 subwoofer wirelessly or

with cables. Ensure that the subwoofer is

positioned, set up and connected in accordance

with the instructions in this guide. You may also

contact your retailer regarding installation.

When handling your subwoofer make sure

to place it on a soft cloth or the like to

avoid making marks on the subwoofer. Do not

hold by or place the subwoofer on the front or

back.

Set up your audio/video product wirelessly

with the BeoLab19 subwoofer. See the

guide enclosed with your transmitter device, for

example BeoLab Transmitter1, for information

about how to connect the transmitter device,

your audio/video product and your subwoofer.

Set the WIRED/WIRELESS switch to WIRELESS.

If you choose a cabled setup, you can use

Power Link or line-in cables for connection

between BeoLab 19 and your audio/video

product. Set the WIRED/WIRELESS switch to

WIRED and the L, R, L+R (left-right) switch

according to how the subwoofer is connected to

the product, see also 9. A splitter can be used if

all Power Link sockets are occupied on the

connected product.

POS.: Set the position switch according to

whether your subwoofer is placed close to

a wall, a corner or in a free-standing position.

Socket and switch panel.

RESET: To reset the wireless setting of the

subwoofer, press and hold the button for a few

seconds until the status indicator starts to ﬂash

green quickly. The subwoofer is now in associate

mode and ready to be connected to the wireless

Power Link device.

SERVICE: For service use only.

GAIN: Adjusts the output level of the

BeoLab 19 compared to the main speakers.

When Beolab 19 is connected to a Bang &

Olufsen TV, there is no need to adjust gain. When

connected to non-Bang & Olufsen products, you

may have to adjust gain.

LP FILTER (low pass ﬁlter): Aligns the

frequency areas in BeoLab 19 and the

speakers. When the switch is set to ON, the knob

can be turned to obtain lower or higher

frequency. When BeoLab19 is connected to a

surround sound system, there is no need to

adjust the LP ﬁlter. When BeoLab 19 is connected

to a Bang & Olufsen audio system, the LP ﬁlter

should be switched on and adjusted to a position

between 40 and 80 which suits most Bang &

Olufsen Power Link speakers. Generally, the

setting of the LP FILTER is dependent on the size

of the main speakers. This means that a larger

speaker requires a lower setting, whereas a

smaller speaker requires a higher setting. When

you connect BeoLab 19 to non-Bang & Olufsen

products, you should listen to music from the

subwoofer and loudspeakers to determine if the

LP FILTER should be adjusted.

PHASE: You may adjust the PHASE if the

sound from the speakers and subwoofer

does not seem to be synchronised. If your

subwoofer is in line with your front speakers,

then set the subwoofer PHASE switch to 0. If

your subwoofer is located anywhere else then try

the phase switch in both positions and set it to

the position that produces the strongest bass at

your listening position. If you notice no

dierence at all, set the switch to 0.

L, R, L+R (left-right switch): Set the switch

according to the connection you have

made to the audio or video product. Bang &

Olufsen televisions can send signals to the

BeoLab 19 via either the left (L) or right (R)

channel. This is set up in the television menus

and the switch should be set accordingly. Usually

when connecting to an audio system, the L+R

position should be used.

Secure the mains cable with the holders

either to the left or the right as illustrated.

The connection cable can run under the holder

together with the mains cable.

Product status and wireless indicator:

– Red (solid): The indicator is solid red for some

seconds when the subwoofer is connected to

the mains or switches o.

– Green (solid): The indicator is solid green for

some seconds when the subwoofer switches on.

– Green (ﬂashing slowly): A software update is in

progress, during which the subwoofer cannot

play. Do not disconnect from the mains.

– Green (ﬂashing quickly): If you have a wireless

Power Link device in your setup, the speaker is

in associate mode and ready to be connected to

the device.

– Orange (solid): The signal strength for a wireless

connection is low.

– Orange (ﬂashing slowly): The product is

overheated and turns down the volume.

– Orange (ﬂashing quickly): An error has occured.

Disconnect the subwoofer from the mains and

reconnect it or reset the network connection, if

you have a wireless Power Link device. If the

problem persists, contact your Bang & Olufsen

retailer.

To see the product labels, remove the front

cover (with Bang & Olufsen logo) by

pulling at the outer edges. Make sure to align

pins and holes when remounting.

Cleaning

Wipe dust o the surfaces using a dry, soft cloth.

If necessary, remove stains or dirt with a soft,

slightly damp cloth and a solution of water and

mild detergent such as washing-up liquid.

Never use alcohol or other solvents to clean any

part of the subwoofer!

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bang Olufsen BEOLAB 19 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info