Bedienungsanleitung Bang Olufsen Beolab5 (Seite 12 von 20) (Englisch)

22653

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Adapt BeoLab 5 to your system

The Acoustic Lens Technology system

in BeoLab5 ensures better balance

between sound in the high and mid

tone frequencies coming directly from

the loudspeaker, and sound reected by

the room. The Acoustic Lens Technology

system also ensures correct tonal

balance in the whole area in front of

theloudspeaker.

The BeoLab 5 Adaptive Bass Control

system and the Acoustic Lens

Technology system ensures optimum

freedom in the placement of your

loudspeakers. Performing a calibration

of the Adaptive Bass Control system

ensures that the loudspeaker is

optimally suited to its placement and

the surroundings – and therefore, gives

the best possible sound quality

Adaptive Bass Control calibration

Normally, when a loudspeaker is placed in a

corner, the bass level is boosted compared to

the bass level in a loudspeaker placed in a

more freestanding position.

With other speaker systems, you have to

consider this when placing them. With

BeoLab5, the Adaptive Bass Control system

–when calibrated – lters out this change in

the bass level.

During the calibration, the loudspeaker

generates a series of sound signals and

measures the response from walls, the oor,

the ceiling, large objects and other surfaces in

the room. Based on these measurements, the

loudspeaker automatically calculates optimal

settings for the Adaptive Bass Control lter.

The ‘Adaptive Bass Control’ calibration ensures that

the bass level suits the placement of the

loudspeaker, and thus the surroundings.

When you switch the loudspeaker on for the rst

time, the indicator light ashes slowly green* –

signalling that it has not yet been calibrated.

Important!

– Before you start the calibration, place the

loudspeaker where you want it to be.

– Do not calibrate more than one loudspeaker at a

time. Otherwise, the sound emitted from one

loudspeaker interferes with the measurements

done in the other, and vice versa.

– Consider the ‘normal status’ of the listening

room: Will the doors be closed…?

The windows…? Will the curtains be drawn…?

Will there be many people in the room…?

– If you, later on, decide to move the loudspeakers,

rearrange your room, carpet the oor, etc., we

recommend that you perform the calibration for

each loudspeaker once again.

– We recommend that you keep any tone control

settings neutral.

During the calibration make sure that no noise

interferes with the sounds emitted by the

loudspeaker. Such noise might, for example, be:

arunning vacuum cleaner, ventilation or air

conditioning systems, motor sounds nearby, etc.

Up to a certain level, the loudspeaker will try to

compensate for this noise, but eventually, the noise

may cause the calibration to fail – indicated by a

slowly ashing red light. Should this happen, you

must restart the calibration – perhaps later on,

when the noise has stopped...

Acoustic Lens Technology –

manufactured under license

fromSausalito Audio Works.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bang Olufsen Beolab5 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bang Olufsen Beolab5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info