Bedienungsanleitung Barbas Cuatro-7 60-60 Opti-Air (Seite 32 von 88) (Englisch)

812708

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

6 Installation requirements

6.1 Requirements on the installation of the appliance in an existing

fireplace

This section refers to the installation of the appliance in an existing open (masonry)

fireplace.

• Make sure that the location agrees with the safety requirements. Refer to section

4.1

• Make sure the opening in the fireplace is large enough for a gap of 1 - 3 cm between

the appliance and the inner fireplace walls .

• Make sure the floor can support the weight of the appliance. Refer to section

for

the weight of the appliance.

• Make sure that the floor temperatures in front of the appliance cannot be higher than

85 °C, during use of the appliance. Refer to section

5.8

• The non-combustible floor in front of the appliance must have a width that extends at

least 150 mm from each side of the appliance and a minimum depth in front of the

appliance according the requirements in section

5.8

• Make sure the room where the appliance is installed is properly ventilated.

• Make sure that combustion air can flow into the appliance without obstruction.

• If applicable, install a valve in the external combustion air pipe.

• The carbon monoxide alarm must be fitted and fixed in place within the same room as

the appliance and can be placed either on the ceiling or wall between 1 meter and 3

meter horizontally from the appliance. If fitting to the ceiling it must be at least 300mm

from any wall. If fitting to a wall, it must be placed as high as possible above any doors

or windows at 150mm below the ceiling.

6.2 Requirements on the installation of the appliance in a new

fireplace

• Make sure the floor is made of concrete or a solid pedestal of nonflammable material.

• Make sure that the floor temperatures under and in front of the appliance are

maximum 85 °C, during use of the appliance. Refer to section

5.3

and section

5.8

• Make sure that the location agrees with the safety requirements. Refer to section

4.1

• Do not install the appliance against a combustible rear wall or combustible side wall.

• Make sure to obey the clearances as listed in section

• Make sure the floor can support the weight of the appliance. Refer to section

for

the weight of the appliance.

• Make sure the room where the appliance is installed is properly ventilated.

• Make sure that combustion air can flow into the appliance without obstruction.

• If applicable, install a valve in the external combustion air pipe.

• If the appliance is equipped with the optional convection ventilator, the combustion air

must be supplied from outside through a flexible aluminum pipe to the appliance.

• Make sure there is an earthed wall socket for the power supply of the convection

ventilator and an earthed wall socket for the power supply of the Opti-Air system.

These sockets must be accessible at all times.

• Make sure the distance between the convection air outlet openings and the ceiling

above is minimum 50 cm.

• Make sure the distance between the convection air outlet openings and a neighboring

wall is minimum 20 cm.

Installation requirements

32 Cuatro-7 60-60

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Barbas Cuatro-7 60-60 Opti-Air Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Barbas Cuatro-7 60-60 Opti-Air

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info