Bedienungsanleitung Barbas Evolux 100-45 (Seite 19 von 32) (Englisch)

812713

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

7.3.4 General firing tips

• The appliance works best when it has heated up as described in chapter

7.3.1

Insufficient heating up leads to a low chimney draught, black deposits on the glass

and incomplete combustion. Good combustion is recognized by bright orange flames,

invisible smoke and no soot deposits on the glass. Use the control lever to get good

combustion. Refer to

6.1

for advice on the required fuel quality.

• Make sure the door of the appliance is closed when in use. Only open the door for

ignition and to refuel.

• Do not remove all the ashes. An ash layer in the combustion chamber forms a heat

insulating layer, that helps the fuel to ignite easy.

• Do not set the control lever in the far left position (all combustion air inlets closed)

when the appliance is used. This will cause severe smoke development, soot

formation and increases the chance of a chimney fire.

• After the first load, do not overload the appliance with fuel. Refer to

6.2

for the

recommended amount of fuel. Too much fuel leads to incomplete combustion, soot

formation and a chance of a chimney fire.

7.4 Firing the appliance with the optional Barbas Opti-Air system

If the appliance has the optional Opti-Air system, the appliance automatically controls the

amount of combustion air. With the Barbas Opti-Air app for Android and iOS it is possible

to select from 3 different combustion levels (quiet combustion , nominal combustion,

fierce combustion) or to select room temperature control.

7.4.1 Installation of the Opti-Air app

1. Download the Barbas Opti-Air app from Google Play (Android) or the App Store

(iOS) and install it on your mobile phone or tablet.

2. Start the Barbas Opti-Air on your mobile device.

3. Make sure bluetooth is on and can recognize other devices.

4. Start to make a connection with bluetooth with device "Airmaster"

5. When asked, enter the PIN code 000000.

6. The app is now ready for use.

Important:

It is possible to install the Barbas Opti-Air on multiple mobile

devices. However, the app can only be active on 1 mobile device at the same

time. Before making connection between the appliance and a second mobile

device, disconnect the bluetooth connection between the appliance and the

first mobile device.

7.4.2 First load and ignition

The Opti-Air system works best with closed door during operation.

Warning:

Do not use the appliance when there is fog or haze or no wind.

Note:

During the first load it is not possible to switch to another combustion level .

To make sure the appliance heats up sufficiently, the Opti-Air system starts

the combustion on the highest combustion level. After the end of the first load

and when the desired flue gas temperature is reached, it is possible to change

the combustion level.

Operation

Evolux 100-45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Barbas Evolux 100-45 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Barbas Evolux 100-45

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info