Bedienungsanleitung Barbas Gas Fire Panorama 70-70 (Seite 8 von 100) (Englisch)

812729

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

4 Requirements

4.1 Requirements on the location

• Never use combustible building materials for the fireplace.

• Do not install the appliance against a flammable rear wall.

• Install a non-flammable insulation plate of at least 12 mm between the appliance and

a non-flammable rear wall. The insulation plate must cover the entire area of the rear

of the appliance.

•For details about the installation, minimum clearances to flammable materials,

permitted insulation materials and air gaps, refer to the "installation and maintenance

manual".

• If the fire burns in the appliance, make sure that the floor temperatures below and in

front of the appliance cannot be higher than 85 °C .

• Make sure that the room where the appliance is installed is properly ventilated.

4.2 Requirements on the convection package (option)

• The convection outlet opening must be at least 1 meter above the appliance.

• No flammable material is present within 30 cm on both sides and 50 cm above the

convection outlet opening.

• The convection outlet opening must be at least 30 cm below the ceiling.

4.3 Other requirements

• The gas supply connection is near the operating unit for an easy connection.

• Only use gas piping of at least ½" and a shut-off valve to connect the gas supply to the

gas regulator block of the appliance.

• Make sure that there is a wall socket with earth connection nearby the appliance. The

socket must be accessible at all times. The power cable (+ 0.5 m) is coming from the

rear of the appliance.

• Install the fireplace on a solid floor that can bear the weight of the appliance and the

fireplace.

• If the floor is made of flammable material, take correct safety measures. Install a

temperature protection plate made of nonflammable material between the appliance

and the floor.

• Install the appliance as a built-in appliance in a new fireplace.

• If the concentric flue system is installed in an existing chimney that is used for wood or

coal fire, clean the chimney.

• If you built a new fireplace, make sure that it is ventilated with vents at the bottom and

top of the fireplace2. If the fireplace is not ventilated the temperature of the appliance

can increase to dangerous temperatures and damage the fireplace.

• Keep a minimum distance between the appliance and flammable mantel pieces. Refer

to the chapter "Mantel piece clearances" in the "installation and maintenance manual":

for the correct minimum clearances.

2An operating unit installed at the bottom of the fireplace surround makes sure enough ventilation air

flows into the fireplace surround and a separate vent at the bottom of the fireplace is not necessary.

Requirements

8Gas Fire Panorama 70-70

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Barbas Gas Fire Panorama 70-70 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Barbas Gas Fire Panorama 70-70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info