Bedienungsanleitung Barbas Unilux 7-55 (Seite 22 von 52) (Englisch)

812929

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

6 Installation

6.1 Installation requirements

6.1.1 Requirements on the installation of the appliance in an existing fireplace

This chapter refers to the installation of the appliance in an existing open fireplace that

before was used for room heating.

• Make sure that the location agrees with the safety requirements. Refer to chapter

4.1

• Make sure the opening in the fireplace is large enough for a gap of 1 - 3 cm at

between the appliance and the inner fireplace walls .

• Make sure the floor can support the weight of the appliance. Refer to chapter

for the

weight of the appliance.

• Make sure that the floor temperatures in front of the appliance cannot be higher than

85 °C, during use of the appliance. Refer to chapter

5.7

• The non-combustible floor in front of the appliance must have a width that extends at

least 150 mm from each side of the appliance and a minimum depth in front of the

appliance according the requirements in chapter

5.7

• Make sure the room where the appliance is installed is properly ventilated.

• Make sure that combustion air can flow into the appliance without obstruction.

• If applicable, install a valve in the external combustion air pipe.

6.1.2 Requirements on the installation of the appliance in a new built fireplace

Important:

• Make sure the floor is made of concrete or a solid pedestal of

nonflammable material.

• Make sure that the floor temperatures under and in front of the appliance

are maximum 85 °C, during use of the appliance. Refer to chapter

5.3

and

chapter

5.7

• Make sure the distance between the underside of the appliance and the

floor is minimum 1 cm.

• Make sure that the location agrees with the safety requirements. Refer to chapter

4.1

• Make sure to obey the clearances as listed in chapter

• Make sure the floor can support the weight of the appliance. Refer to chapter

for the

weight of the appliance.

• Make sure the room where the appliance is installed is properly ventilated.

• Make sure that combustion air can flow into the appliance without obstruction.

• If applicable, install a valve in the external combustion air pipe.

• Make sure there is a 3 mm clearance on the sides and top of the appliance to allow for

expansion of the appliance during use.

• Install ventilation openings near the bottom and near the top of the fireplace surround,

to avoid heat accumulation in the fireplace surround.

• Make sure the total ventilation air inlet openings have a minimum area of 450 cm2. (2

inlet openings of minimum 225 2.)

• Make sure the total ventilation air outlet openings have a minimum area of 450 cm2. (2

outlet openings of minimum 225 cm2.)

Installation

22 Unilux-7 55

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Barbas Unilux 7-55 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Barbas Unilux 7-55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info