Bedienungsanleitung Barbecook Spring 3112 (Seite 7 von 100) (Alle Sprachen)

790886

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

www.barbecook.com 7

When the gas is on its way to the burners, it passes through the

venturis. Thanks to the holes at the sides, the gas is then mixed

with air and - as a result - with oxygen. This is necessary for a

good ignition in the burners: only the correct mixture of gas and

oxygen will ignite properly and will result in nice ﬂames.

4.2 Burner hoods

The burner hoods are the hoods that you mount above the

burners of your appliance. They protect the burners from

dripping fat. The holes at the sides of the hoods also distribute

the heat over the grill, so it is heated much taster and more

evenly.

4.3 Enamel

Some parts of the appliance are covered in a layer of melted

glass, called enamel. This enamel protects the underlying metal

from corrosion. Enamel is a high-quality material: it is resistant to

rust, does not fade under the inﬂuence of high temperatures and

is very easy to maintain.

Because the enamel is less ﬂexible than the metal which

the appliance incorrectly. To avoid problems, be careful

when assembling enamelled parts and always maintain

the enamel as described further in this manual.

4.4 Flare-ups

Flare-ups are sudden ﬂames that spark from the bowl when you

are grilling. They are usually caused by dripping fat or marinade.

5 ASSEMBLING THE APPLIANCE

5.1 Safety instructions

• Do not modify the appliance when assembling it. lt is very

dangerous and not allowed to alter parts that are pre-

assembled and/or sealed by the manufacturer.

• Always follow the assembly instructions carefully.

• The user is responsible for the correct assembly of the

appliance. Damages caused by improper assembly are not

covered by the warranty.

5.2 To assemble the appliance

You need a cross-slotted screwdriver, a ﬂat-slotted screwdriver

and an AA battery (electrical igniter). There are no batteries

supplied with the appliance.

1. Put the appliance on a ﬂat and clean surface.

2. Assemble the appliance as shown on the assembly

drawings. You ﬁnd them in the second part of this manual,

after the exploded view of your appliance.

Be careful when assembling enamelled parts. The tools

and screws may damage the enamel. Use the provided

ﬁber washers to protect the enamel around the screws.

The blister packs can contain more screws than

necessary. Screws can be left over after the assembly.

The package includes an emergency kit with spare

assembly parts (screws, beits, ﬁber washers ... ) You can

use them in case you lost or broke some parts.

6 CONNECTING GAS TO THE

APPLIANCE

6.1 Which cylinder, hose and regulator?

Before you can connect gas to the appliance, you have to buy

a gas cylinder, hose and pressure regulator. The table below

shows you which cylinder, hose and regulator you have to use.

In Belgium (BE), for example, you have to use a propane cylinder

with a hose and regulator for 37 mbar or a butane cylinder with a

hose and regulator for 28-30 mbar.

This barbecue has been adjusted to be operate with 4,5

to 15 kg butane/propane cylinders with an appropriate

low pressure regulator. We recommend connecting the

appliance to propane. Propane oers a high-quality

combustion and is less sensitive to frost. The height H of

the cylinder must be less than 70 cm, regardless of the

cylinder’s width or diameter D.

Buy your pressure regulator and gas cylinder together.

Not all regulators ﬁt all cylinders.

Use only a gas hose and regulator that is homologated

for the country of use.

6.2 Safety instructions

• Never connect the cylinder directly to the appliance. Always

mount a pressure regulator on the cylinder ﬁrst.

• Never modify pre-assembled or sealed parts of the cylinder,

the hose or the pressure regulator.

• Keep the hose as short as possible (1,5 m maximum) to

prevent it from dragging on the ground.

• Never distort or twist the hose. Do not pull or pierce

the hose.Keep the hose away from any parts of the

barbecue that get hot. Check that the ﬂexible hose

stretches out normally, without twisting or pulling.

• It should be replaced if it is damaged or cracked, when

required by national regulations or at the end of the part

lifecycle (f.ex France)

• Never open the gas supply.

• Always keep the cylinder in an upright position.

• Check for leaks each time you make changes to the gas

connection. See “7 Checking for gas leaks”.

6.3 Connecting the hose to the appliance

France:

The equipment may be used with two types of ﬂexible hose:

• Flexible hose designed to be joined onto ringed tailpieces

on both the barbecue and regulator sides, held ﬁrm

with collars (in accordance with standard XP D 36-110).

recommended length 1.25 m.

• Flexible hose (according to standard XP D 36-112) ﬁtted

with a G 1/2 threaded nut for ﬁxing to the barbecue

and a M 20 x1.5 threaded nut for ﬁxing to the regulator,

recommended length 1.25 m.

ES, GB,, IE, PT, BE,

FR, LU, IT, CY

DK, GR, NO, SE, EE,

LT, LV, CZ, PL, MT,

HU, SI, SK, NL

Country Cylinder, hose and

regulator

Propane, 30 mbar /

Butane, 30 mbar

Propane, 37 mbar /

Butane, 28-30 mbar

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Barbecook Spring 3112 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info