Bedienungsanleitung Barbecook Spring 330 (Seite 14 von 346) (Alle Sprachen)

616233

Zoom out

Zoom in

Vorherige Seite

1/346

Nächste Seite

14 www.barbecook.com

11.4 Maintaining enamel, stainless steel,

chrome and powder coated parts

The appliance is composed of enamelled, stainless steel,

chromed and powder coated parts. Each material has to be

maintained differently:

To prevent formation of rust on stainless steel, avoid

contact with chlorine, salt and iron. We recommend not

using the appliance near the coast, near railways or near

swimming pools.

Damages caused by not following these instructions are

regarded as inadequate maintenance and are not

covered by the warranty.

Below the exploded view of your appliance (second part of the

manual), you find a list with all parts of which the appliance is

composed. This list includes a symbol that specifies the material

of each part, so you can use it to check how you have to maintain

a particular part. The parts lists use the following symbols:

11.5 Storing the appliance

If you do not use your appliance for a longer period of time, store

it in a dry place. Before you store the appliance:

• Disconnect the gas cylinder. Never store your appliance

indoors (not even in a garage or shed) as long as it is

connected to the gas cylinder.

• Clean the burners and the grills, rub them with oil and wrap

them in paper.

• Cover your appliance with a Barbecook cover. Register your

appliance at www.barbecook.com to find out which cover

you need.

11.6 Storing gas cylinders

These instructions apply to both empty and full gas cylinders.

• Always store gas cylinders outdoors, in a well-ventilated

area. Make sure they are not exposed to excessive heat or

direct sunlight.

• Never store a gas cylinder in an area that can become very

hot (in a car, on a boat...).

• Never store your gas cylinder or spare gas cylinder in the

cabinet of your appliance.

• Never store your spare gas cylinder near a gas appliance in

use.

• Always store gas cylinders outside the reach of children.

• Always store and transport gas cylinders in upright position.

11.7 Ordering spare parts

Parts that are directly exposed to fire or intense heat have to be

replaced from time to time. To order a spare part:

1 Look up the reference number of the part you need. You find

a list of all reference numbers below the exploded views in

the second part of this manual and on www.barbecook.com.

If you registered your appliance online, you will

automatically be guided to the correct list.

2 Order the spare part at your point of sale. You can order

parts both under and outside warranty.

12 WARRANTY

12.1 Covered

Your appliance comes with a warranty of two years, starting from

the date of purchase. This warranty covers all manufacturing

defects, provided that:

• You used, assembled and maintained your appliance

according to the instructions in this manual. Damages

caused by misuse, incorrect assembly or inadequate

maintenance are not regarded as manufacturing defects.

• You can present the receipt and the unique serial number of

your appliance. This serial number starts with a G, followed

by 15 digits. You can find it:

• On this manual and on the starter pack that included the

manual.

• On the packaging of the appliance.

• On the type label on the inside of the cabinet door

(Quisson, Siesta 4 and Siesta 6) or on the inside of the

bottom front panel (Spring, Siesta 2 and Siesta 3).

• The Barbecook quality department confirms that the parts

are defective and that they proved defective under normal

use, correct assembly and adequate maintenance.

If one of the above conditions is not met, you cannot claim any

form of contribution. In all cases, the warranty is limited to the

repair or replacement of the defective part(s).

12.2 Not covered

The following damages and defects are not covered by the

warranty:

• Normal wear and tear (rusting, distortion, discolouration...) of

parts that are directly exposed to fire or intense heat. It is

normal to replace these parts from time to time.

• Visual irregularities that are inherent to the manufacturing

process. These irregularities are not regarded as

manufacturing defects.

• All damages caused by inadequate maintenance, incorrect

storage, improper assembly or modifications made to

pre-assembled parts.

Material How to maintain this material

Enamel

• Do not use sharp objects and do not knock

against a hard surface.

• Avoid contact with cold liquids while still hot.

• You can use metal sponges and abrasive

detergents.

Stainless steel

and chrome

• Do not use aggressive, abrasive or metal

detergents.

• Use soft detergents and let them act on the

steel.

• Use a soft sponge or cloth.

• Rinse thoroughly after cleaning and dry well

before storing.

Powder

coated

• Do not use sharp objects. Use soft detergents

and a soft sponge or cloth.

• Rinse thoroughly after cleaning and dry well

before storing.

Symbol Material

Enamel

Chrome

Stainless steel

Powder coated

!gas_spring_standard.book Page 14 Tuesday, July 29, 2014 2:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Barbecook Spring 330 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info