Bedienungsanleitung Bartscher Deltamat TF 50 (Seite 18 von 18) (Englisch)

554330

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

page 36

USER SECTION

10. TROUBLESHOOTING

N.B. For any other problems, contact the Technical Assistance service.

The manufacturer reserves the right to alter the technical characteristics without prior notice.

Type of Problem Possible Causes Cure

The appliance does not start The main switch is turned off Turn on the switch

The appliance does not

draw water

The water tap is closed Open the water tap

The rinsing arm nozzles or the

electrovalve lter are clogged and/or

caked with lime deposits

Clean the rinsing arm nozzles, the pipes and the electrovalve

lter. If the machine has a water purier check the salt content

or regenerate the resins more often

Faulty pressure switch Replace the pressure switch (call the Technical Assistance

service)

Flashing of the cycle lamp See chapter 7 "Alarms"

Unsatisfactory washing

results

The washing nozzles are clogged or

the washing arms do not rotate

Unscrew and clean the nozzles and the rotating column, ret

them correctly in their seats

Unremoved grease or starch Detergent concentration too low

The lter is too dirty Remove the lter, clean it with a brush under running water and

ret in its seat

Check the tub temperature (it must

be between 50°C and 60°C)

Adjust the thermostat or check correct heating element opera-

tion

Length of washing cycle inadequate

for type of grime build-up

Choose a longer cycle if possible, otherwise repeat wash cycle

Wash water too dirty Empty water from the tub, clean lters; rell the tub and correct-

ly reposition the lters

Presence of foam Use of unsuitable products Use non-foaming detergent or use less of same detergent

Tub temperature too low Adjust the thermostat or check correct heating element opera-

tion

Glasses or dishes are not

completely dry

Insufcient rinse aid Increase the amount of rinse aid by turning the screw on the

dispenser (see paragraph "Rinse aid dispenser")

The rack is unsuitable for the glasses

and dishes

Use a suitable rack enabling the dishes to be tilted so water can

run off

The dishes have been too long in the

tub

As soon as the wash cycle is nished, pull the rack out imme-

diately, allowing the air to dry the glasses and dishes more

quickly

Rinse water temperature is less than

75°C - 80°C

Check the temperature of the boiler thermostat

Surface of dishes and glasses too

rough or porous for material wear

Replace type of dishes and glasses used

Streaks and spots on glas-

ses and dishes

Too much rinse aid Decrease the amount of rinse aid by turning the ne-adjustment

screw on the dispenser (see paragraph "Rinse aid dispenser")

The water is too hard Check the water hardness. Water should not be harder than

5-10 °f

For appliances with conditioners:

too little salt in the salt container or

the resins have not been properly

regenerated

Fill the salt container (coarse salt: 1-2 mm grains) and regene-

rate the resins more often. If lime deposits are also observed on

the body of the machine, have a qualied technician check the

operation of the purier

Salt present in dishwasher tub Thoroughly clean and rinse the appliance, and avoid spilling salt

when lling the container

The appliance suddenly

stops during the cycle

The appliance is connected to an

overloaded circuit

Connect the appliance separately (call the Technical Assistance

service)

A safety device has been activated Check safety devices (call the Technical Assistance service)

During wash cycle the

machine stops and draws

water

Water from the previous day has not

been replaced

Empty the tub and rell it

The tub water temperature is too high Have the Technical Assistance service check the thermostat and

the pressure switch

Faulty pressure switch

The overow tube is incorrectly

positioned

Remove the overow tube and correctly reposition it

The booster pump can't

prime

Little pressure on feeding Take out the boiler pipe and drain the pump

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bartscher Deltamat TF 50 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bartscher Deltamat TF 50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info