Bedienungsanleitung Bartscher Deltamat TF (Seite 18 von 22) (Englisch)

554388

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

page 41

Asuitableomni-polar,one-wayswitchshallbeinstalledandsizedaccordingtotheabsorption

provided, with a contact opening of at least 3 mm. This switch shall be solely and exclusively

used for this purpose and installed in the immediate vicinity of the machine, installed in full

respect of the local laws. Always turn the machine off via this switch. This is the only model

of switch that guarantees a total electrical power disconnection.

6.2.3 Water supply connection - Characteristics

*Should the water supply pressure be more than 400 kPa, a pressure reducer must be

installed (only for those versions where it is not a standard supply, already).

**It is compulsory to install a water-softener, in case of water with average hardness

above 8°f. Washed objects will be cleaner and the machine will last much longer.

The machine can be equipped with a water softener, on request. If the machine is equipped

with a water-softener, a regeneration of the resins shall be done on regular basis (see par.

2.6).

N.B.: Any damage caused by limestone (calcareous water higher-up than 8°F and without

water-softener) will not be covered by warranty.

A periodical check of the supplied water hardness is highly recommended.

***The water supply temperature shall never exceed 55°C.

The drain tube shall always be connected to a siphon in order to prevent the release of

odors.

Maximum drain height = cm. 50.

6.2.4 Steam evacuation

In accordance with regulations of environmental hygiene, for the proper functioning of the

machine and a healthy environment for the operator who working in there, it should be at

least 10 air volume changes per hour in the room where the machine is installed.

For small wash rooms we recommend at least 15 air volume changes per hour

6.3 Installation

6.3.1 Positioning the machine

Remove the packing with care.

Lift the machine as described in chap. 6.1.1 " Handling the product".

Position the machine as shown on the installation diagram (lay-out) approved at the time

of the offer.

Maintain a minimum distance of about 50 mm from the walls, so that motors are ventilated.

Install suction hoods to assure proper ventilation of the room, in order to eliminate steam

and excessive humidity.

Check that the machine is properly levelled, by adjusting the legs.

Makesurethemachineisnotstandingonthepowercableoronthelling/drainhoses.

Levelthemachineat,byadjustingthesupportfeet.

Water characteristics table Min Max

Static Pressure 200Kpa 600Kpa

Dynamic Pressure* 150Kpa 400Kpa

Water hardness** 5°f 20°f

Cold water-supply tempe-

rature

5°C 15°C

Hot water-supply tempera-

ture***

45°C 50°C

Table 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bartscher Deltamat TF Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bartscher Deltamat TF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info