Bedienungsanleitung Batavia BT-CBCD001 - 7062722 (Seite 7 von 26) (Deutsch, Englisch, Holländisch, Französisch)

758250

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English

being undertaken. A minimum rating of

FFP2 is recommended. If operating the

tool causes discomfort in any way, stop

immediately and review your method of

use.

• Battery chargers are for indoors use

only. Ensure that the power supply and

charger are protected against moisture

at all times.

• Ensure that the lighting is adequate.

• Ensure that the drill bit is securely xed

in the chuck. Insecure drill bits can be

ejected from the machine causing a

hazard.

• Ensure that the drill bit is not in contact

with the workpiece prior to starting up

the tool.

• Before drilling, check that there is suf-

cient clearance for the drill bit under the

workpiece.

• Drill bits get hot during operation, allow

to cool prior to handling them.

• NEVER use your hands to remove saw-

dust, chips or waste close by the bit.

• Examine the chuck regularly for signs of

wear or damage. Have damaged parts

repaired by a qualied service centre.

• ALWAYS wait until the drill has come to

a complete stop before putting it down.

3. Before use

• Avoid damage that can be caused by

screws, nails and other elements in your

workpiece; remove them before you

start working.

• Use suitable detectors to nd hidden

utility lines or call the local utility com-

pany for assistance (contact with elec-

tric lines can lead to re or electrical

shock; damaging a gas line can result in

an explosion; penetrating a water pipe

will cause property damage or an elec-

trical shock).

• Secure the workpiece (a workpiece

clamped with clamping devices or in a

vice is held more securely than by

hand).

4. During use

• Hold power tool by insulated gripping

surfaces (8), when performing an oper-

ation where the cutting accessory or

fastener may contact hidden wiring

(cutting accessory and fasteners con-

tacting a “live” wire may make exposed

metal parts of the power tool “live” and

could give the operator an electric

shock).

• In case of electrical or mechanical mal-

function, immediately switch off the

tool or unplug charger from power

source.

5. Before rst use

Remove the machine and the accessories

from the packaging. Check the machine for

transport damage and do not use the

machine in case of damages. Keep the

packing materials away from children, risk

of suffocation!

6. Intended use

The cordless hammer drill/screwdriver is

designed for tightening and undoing screws,

for drilling in wood, metal and plastic, and

for hammer drilling in stone, in each case

when using the appropriate bits. The equip-

ment is to be used only for its prescribed

purpose.

7. Operation

7.1 Direction control

• The direction of rotation can be set

using the Forward/Reverse Switch (7).

• For anti-clockwise rotation, push the

switch to the right.

• For clockwise rotation, push the switch

to the left.

Note: When the Forward/Reverse Switch is

in the central position, the drill is locked and

cannot be switched on. Use this setting as a

safety feature to prevent the drill from being

switched on accidentally.

7.2 Mode selector

The clutch settings are indicated by the

symbols on the Mode Selector (4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-CBCD001 - 7062722 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info