Bedienungsanleitung Batavia BT-CBID001 - 7062808 (Seite 7 von 22) (Deutsch, Englisch, Holländisch, Französisch)

758162

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

English

aged parts repaired by a qualied ser-

vice centre.

• ALWAYS wait until the drill has come to

a complete stop before putting it down.

3. Before use

• Avoid damage that can be caused by

screws, nails and other elements in your

workpiece; remove them before you

start working.

• Use suitable detectors to nd hidden

utility lines or call the local utility com-

pany for assistance (contact with elec-

tric lines can lead to re or electrical

shock; damaging a gas line can result in

an explosion; penetrating a water pipe

will cause property damage or an elec-

trical shock).

• Secure the workpiece (a workpiece

clamped with clamping devices or in a

vice is held more securely than by

hand).

4. During use

• Hold power tool by insulated gripping

surfaces (6), when performing an oper-

ation where the cutting accessory or

fastener may contact hidden wiring

(cutting accessory and fasteners con-

tacting a “live” wire may make exposed

metal parts of the power tool “live” and

could give the operator an electric

shock).

• In case of electrical or mechanical mal-

function, immediately switch off the

tool or unplug charger from power

source.

5. Before rst use

Remove the machine and the accessories

from the packaging. Check the machine for

transport damage and do not use the

machine in case of damages. Keep the

packing materials away from children, risk

of suffocation!

6. Intended use

The cordless impact driver is designed for

tightening and undoing screws.

The equipment is to be used only for its

prescribed purpose.

7. Operation

7.1 Direction control

• The direction of rotation can be set

using the Forward/Reverse Switch (7).

• For anti-clockwise rotation, push the

switch to the right.

• For clockwise rotation, push the switch

to the left.

Note: When the Forward/Reverse Switch is

in the central position, the drill is locked and

cannot be switched on. Use this setting as a

safety feature to prevent the drill from being

switched on accidentally.

7.2 Fitting a driver bit

WARNING: DO NOT t any attachment with

a maximum speed lower than the no load

speed of the machine.

1. Pull the Collar (2) of the Hex Bit Holder

(1) forward, and insert the bit.

2. Release the Collar.

3. Pull on the bit to check that it is

securely tted. If the bit is not secure,

repeat the above procedure.

Note: Make sure screwdriver bits used are

hardened and suitable for use with an

impact driver.

7.3 Switching the machine on and off

The on/off switch (4) is used for activating

the machine and adjusting rotation speed.

• Pressing the on/off switch (4) will acti-

vate the machine, the further the switch

is being pushed, the faster the drill will

turn.

• Releasing the on/off switch (4) will stop

the machine.

WARNING: If the power tool gets exces-

sively hot in use, stop using the tool immedi-

ately and allow to cool before continuing

work. The cooling period can be reduced by

operating the drill at maximum speed with

no load. Always make sure the Motor Vents

(3) are not blocked and do not allow dust to

enter the body of the tool through the Motor

Vents; dust, especially metallic dust, may

damage or destroy the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-CBID001 - 7062808 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info