Bedienungsanleitung Batavia BT-CCD001 - 7062504 (Seite 12 von 26) (Deutsch, Englisch, Holländisch, Französisch)

758263

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English

Selection:

Mode selector Torque selector Speed

Screwing 1 – 16* 1

Drilling Masonry /

Concrete

N/A 2

Drilling Wood N/A 1 or 2

Drilling Metal N/A 1 or 2

• Select a low setting for small screws or

soft work material.

• Select a high setting for large screws, hard

work materials and when removing

screws.

• You should preferably choose a setting as

low as possible when driving screws.

Select a higher setting if the motor slips

before the screw is fully tightened.

WARNING: If the power tool gets excessively

hot in use, stop using the tool immediately and

allow to cool before continuing work. The cool-

ing period can be reduced by operating the

drill at maximum speed with no load. Always

make sure the Motor Vents (6) are not blocked

and do not allow dust to enter the body of the

tool through the Motor Vents; dust, especially

metallic dust, may damage or destroy the tool.

Switching the machine on and off

The on/off switch (13) is used for activating the

machine and adjusting rotation speed.

• Pressing the on/off switch (13) will activate

the machine, the further the switch is

being pushed, the faster the drill will turn.

• Releasing the on/off switch (13) will stop

the machine.

LED lamp

The LED lamp (14) will be lit automatically as

soon as you press the ON/OFF switch (13).

ACCESSORIES

Use only accessories with an allowable speed

matching at least the highest no-load speed of

the tool

MAINTENANCE AND CLEANING

WARNING: Always disconnect from the mains

power supply, before carrying out any mainte-

nance/ cleaning of the charger. Remove the

battery before carrying out any maintenance/

cleaning of the tool.

Maintenance

There are no inner parts of the tool which need

maintenance.

Cleaning

• Keep safety devices, ventilation openings

and the motor housing as free as possible

from dirt and dust. Rub the electric power

tool with a clean cloth or blow over it with

low pressure compressed air.

• We recommend that you clean your elec-

tric power tool immediately after each use.

• Clean the electric power tool regularly with

a damp cloth and somewhat soft soap.

Do not use any cleaning or solvent materials;

these can attack the device’s plastic compo-

nents. Make sure that no water can get inside

the electric power tool.

TECHNICAL DATA

Speed . . . . . . . . . . 0 – 350 / 1200 min-1

Impacts per Minute. . .0– 6000 / 20 000 min-1

Chuck . . . . . . . . . . . . . . . 2 – 13 mm

Torque hard/soft . . . . . . . . . . 25 / 48 Nm

Dimensions . . . . . . . . . .23 × 10 × 22 cm

Weight . . . . . . . . . . . . . . . . . 1.28 kg

Sound Pressure Level LpA . . . . 80.80 dB(A)

Uncertainty KpA . . . . . . . . . . . . . . 3 dB

Sound Power Level LWA . . . . . 91.80 dB(A)

Uncertainty KWA. . . . . . . . . . . . . . 3 dB

Hand Arm Vibration

(No Load) . . . . . . . . . . . . . . 0.748 m/s2

(In Metal) . . . . . . . . . . . . . . 1.753 m/s2

(In Masonry) . . . . . . . . . . . . 18.83 m/s2

Uncertainty K. . . . . . . . . . . . . .1.5m/s2

7062504-Cordless_Combi_Drill-Ma-1702-06.indb 10 27-09-17 09:18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-CCD001 - 7062504 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info