Bedienungsanleitung Batavia BT-CCS003 - 7062508 (Seite 9 von 19) (Deutsch, Englisch, Holländisch, Französisch)

758238

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

English

14 15

English

• Fit the required blade, making sure the

direction indicator on the face of the blade

is in the same direction as the Direction

Indicator (23).

• Re-t the Blade Flange, washer and Blade

Securing Bolt. Press in the Spindle Lock

Button and tighten using the hex key.

• Ensure the blade is secure before use.

SETTING BEVEL ANGLE

• This saw is equipped with a tilting Base

Plate (14). This allows bevel cuts to be

made.

• Alter the angle of the Base Plate by loos-

ening the Bevel Angle Locking Knob (21).

The Base Plate will now be free to pivot.

• Select the angle required (0 – 45°) using

the Bevel Angle Gauge (22) and retighten

the Bevel Angle Locking Knob.

• Ensure accuracy by checking the angle

between the Blade (13) and the Base

Plate using a suitable protractor.

SETTING DEPTH ADJUSTMENT

• This saw is equipped with a depth adjust-

ment mechanism.

• Alter the depth of the cut by loosening the

Depth Locking Knob (11). The Base Plate

(14) is now free to adjust to the required

depth.

• Adjust the Base Plate to the required

depth using the Depth Scale (12) or a ruler

and retighten the Depth Locking Knob.

• When set correctly, the blade teeth should

project approximately 3mm from the

underside of the material being cut.

MAINTENANCE AND CLEANING

WARNING: Always disconnect from the mains

power supply, before carrying out any mainte-

nance/ cleaning of the charger. Remove the

battery before carrying out any maintenance/

cleaning of the tool.

Cleaning

• Keep safety devices, ventilation openings

and the motor housing as free as possible

from dirt and dust. Rub the electric power

tool with a clean cloth or blow over it with

low pressure compressed air.

• We recommend that you clean your elec-

tric power tool immediately after each use.

• Clean the electric power tool regularly with

a damp cloth and somewhat soft soap.

Do not use any cleaning or solvent materials;

these can attack the device’s plastic compo-

nents. Make sure that no water can get inside

the electric power tool.

Maintenance

There are no inner parts of the tool which need

maintenance.

TECHNICAL DATA

No load speed . . . . . . . . . . . 3650 min-1

Blade size . . . . . . . . . . . . . Ø 165 mm

Blade bore . . . . . . . . . . . . . . Ø 16 mm

Max depth of cut . . . 0° :50mm / 45° :36mm

Dimensions . . . . . . . . . . 32 x 18 x 25 cm

Weight . . . . . . . . . . . . . . . . . 2.77 kg

Sound Pressure Level LpA . . . . .81.47 dB(A)

Uncertainty KpA . . . . . . . . . . . . . . 3 dB

Sound Power Level LWA . . . . . 93.47 dB(A)

Uncertainty KWA. . . . . . . . . . . . . . 3 dB

Hand Arm Vibration

(No Load) . . . . . . . . . . . . . .1.264 m/s2

Uncertainty K. . . . . . . . . . . . . .1.5m/s2

BEFORE USE

• Avoid damage that can be caused by

screws, nails and other elements in your

workpiece; remove them before you start

working.

• Use suitable detectors to nd hidden utility

lines or call the local utility company for

assistance (contact with electric lines can

lead to re or electrical shock; damaging a

gas line can result in an explosion; pene-

trating a water pipe will cause property

damage or an electrical shock)

• Secure the workpiece (a workpiece

clamped with clamping devices or in a

vice is held more securely than by hand)

BEFORE FIRST USE

Remove the machine and the accessories from

the packaging. Check the machine for trans-

port damage and do not use the machine in

case of damages. Keep the packing materials

away from children, risk of suffocation!

INTENDED USE

Hand-held battery-powered electric circular

saw for cross, rip and bevel cutting of hard and

softwood timber and sheet material.

OPERATION

• Before using the saw, practise on scrap

material. The settings of the machine are

crucial to achieving a good quality nish,

and your work could easily be damaged

by using an incorrect setting.

Handling your circular saw

• Always hold the saw securely, with both

hands, by the handles provided.

• Always allow the blade to come to a com-

plete stop before placing the machine

down.

• Always make sure that work will not move

whilst being cut. Use clamps where

appropriate.

Making a cut

• Hold the saw securely and rest the front

edge of the Base Plate (14) on the edge of

the workpiece.

• Check the blade is not in contact with the

workpiece or any other object.

• Start the machine by pressing in the Lock

Off Button (2) and squeezing the On/Off

Trigger (3).

Note: The saw is tted with two Lock Off But-

tons - one on each side of the saw - to allow

left or right-handed operation.

• Allow the motor to reach full speed and

push the saw forwards smoothly across

the workpiece.

• Maintain a steady movement and ensure

the Base Plate is kept pressed against the

workpiece.

Note: The front edge of the Base Plate fea-

tures an indentation. For normal 0° cutting,

align the left side, 0° Line (19) with the line to

be cut, for 45˚ bevel cutting align the right side,

45° Line (20) with the line to be cut.

• Allow the blade to pass through the mate-

rial and release the On/Off Trigger. Alter-

natively, if the cut does not reach the edge

of the workpiece, release the On/Off Trig-

ger and allow the blade to stop moving

before lifting out of the cut.

• Do not place the machine down until the

blade has stopped completely.

FITTING AND REMOVING BLADES

WARNING: Remove battery pack if tted.

WARNING: Wear cut-proof gloves when han-

dling sharp blades.

• Always check the blade being tted is

suitable for the material being cut.

• Only t blades that are in perfect condi-

tion. Blunt, bent, and cracked blades

should be discarded.

• Press in the Spindle Lock Button (26) and

carefully rotate the blade by pushing on

the side face of the saw blade until the

spindle lock engages. Unscrew the Blade

Securing Bolt (16) anti-clockwise using

the supplied hex key.

• Remove the Blade Securing Bolt, washer

(if tted) and Blade Flange (17).

• Use the Lower Guard Lever (25) to rotate

the Lower Guard out of the way.

Batavia BT-CCS003 - 7062508 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info