Bedienungsanleitung Batavia BT-CHG001 - 7063519 (Seite 6 von 24) (Deutsch, Englisch, Holländisch, Französisch)

757990

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

English

3. Before rst use

Remove the machine and the accessories

from the packaging. Check the machine for

transport damage and do not use the

machine in case of damages. Keep the

packing materials away from children, risk

of suffocation!

4. Contents of packing

1× Cordless heat gun

1× Flat nozzle

1× Reection nozzle

1× Concentration nozzle

1× Operating instructions

5. Intended use

The heat gun is designed for the following

elds of application:

• for removing varnish or oil paint and

latex paint, stickers,

• for removing ski wax, putty and for

loosening rusty or tight nuts and

screws,

• for melting ice in frozen metal pipes and

locks,

• for shrinking packaging lms and

shrink-lm hoses,

• for loosening ooring,

• for deforming plastics,

• for drying acceleration of paint, varnish,

wet or damp substances or objects

before they are further processed,

• for torching wooding casings.

WARNING!

• Please note that glazes and base coats

on wood cannot be removed with the

heat gun.

• First test on a small not visible section

of the surface before processing a

larger area.

• Vapours of paints and plastics are poi-

sonous. Always ensure adequate venti-

lation, while working in buildings and

use inhalation protection, if necessary.

• Do not use chemical paint stripper or

solvent at the same time when using

the heat gun.

• For removing paint and varnish, direct

the heat gun nozzle from approx. 10 cm

distance onto the paint, until it starts

bubbling. Push the paint in the blowing

direction off its substrate.

• From proled surfaces, remove the

paint after heating by using a wire

brush.

• Areas that should not to be heated up,

please cover with a non-ammable and

poorly heat conducting material.

• Before cleaning the unit, always unplug

and allow the heat gun to cool down

fully.

6. Mounting the nozzle

(See Fig. B)

WARNING: Always remove the battery from

the device before attaching or removing the

nozzle.

a. Insert the desired nozzle (A, B, C) into

the tool collet and push it rmly.

b. To remove the nozzle, turn the tool

collet counter clockwise and take out

the nozzle.

7. Rafter hook

(See Fig. C, D)

With the provided rafter hook (3) you can

fasten the heat gun on a suitable place.

a. First lift up the spring-loaded rafter

hook (3) and then take it out of the hole.

b. Fasten the rafter hook on a suitable

place, so you will have the heat gun

ready to hand.

8. ON/OFF switch

WARNING: Always wear adequate personal

protection equipment when setting up and

operating the tool. The safety switch (4) is

always in the central position, thus the heat

gun is locked and cannot be switched on.

a. To start the tool, rst push the safety

switch (4) to the right or to the left and

then squeeze the trigger switch (6).

b. Release the trigger switch to stop the

heat gun.

ATTENTION! The motor will still run for

approx. 6 seconds. This is necessary in

order to cool down the motor.

Note: The heat gun reaches operating tem-

perature within a few seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-CHG001 - 7063519 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info