Bedienungsanleitung Batavia BT-CS015 - 7063409 (Seite 13 von 50) (Deutsch, Englisch, Holländisch, Französisch)

758291

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

English

13. Laser beamer

13.1 Laser beamer in use

The leading beam of the laser beamer

makes sawing in straight lines much easier:

a. along a drawn line, or

b. by aligning it to a xed point marked on

the workpiece.

The range of the laser beam, depending on

the environmental light, is about 65 cm.

13.2 Replacing batteries

• Hold the circular handsaw straight in

front of you. Pull the lid on the laser

beamer towards you, and then lift it.

Replace the batteries with new ones.

You will need 2 x 1.5 V “LR44” batteries.

• Never dispose of old/empty batteries

with the household refuse, but deposit

them instead at special collection point

for batteries or chemical refuse.

• When inserting the batteries, ensure

that the +/- terminals are correctly

placed, as shown inside the battery

compartment.

• Again lower the lid, pull it towards you,

press it against the saw blade cover,

and let it softly spring back into the

closed position.

• Check that the laser beamer is properly

closed by carefully opening the lid

straight upwards. If the lid opens up,

repeat the closing procedure, until the

lid stays properly closed.

13.3 Adjusting the laser beam

• Transport handling and heavy use can

affect the precision of the laser beam.

• The laser beam itself can be easily

adjusted.

• Hold the blade of the circular saw

against a straightedge or perfectly

straight plank.

• Switch the laser on.

• Check whether the laser beam runs

parallel along the edge of the straight-

edge or plank.

If the laser beam is out of alignment, pro-

ceed as follows:

• Loosen the screw on the front side of

the laser a few turns.

• Hold the blade of the circular saw

against a straightedge or perfectly

straight plank.

• Correct the laser such that it runs dead

straight along the edge.

• Again tighten the screw.

14. Cleaning and maintenance

• To avoid injury always pull the power

plug before maintaining or cleaning the

machine.

• Clean the machine with a moist cloth.

• If the machine is very dirty use a mild

detergent or soap on the cloth. Other

cleaning agents may contain chemical

substances which may damage the

plastic parts of the machine.

• Do not allow liquids to enter the

machine and do not immerse the

machine in liquids of any kind.

• Repairs, inspections of the interior of

the machine, adjustments and replace-

ment of the carbon brushes may only

be undertaken by a professional. Only

identical replacement parts may be

used! For further information please

contact our customer service

department.

• Always keep the ventilation slots open

and clean. After each use remove dirt

and contaminations with a brush or

blow it out with compressed air.

• If increased brush re occurs this indi-

cates that the carbon brushes are worn

and should be replaced. Have the

brushes replaced by a professional.

7062848-Circular_Saw_1400W-Ma-1803-19.indb 11 20-03-18 10:39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-CS015 - 7063409 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info