Bedienungsanleitung Batavia BT-DSR001 - 7061488 (Seite 12 von 20) (Deutsch, Englisch)

758131

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

With the triangular sanding plate, the sander

is perfect for sanding corners and edges

that are difcult to reach. If necessary, use

the tip or an edge of the sander plate to

sand proled sections.

By changing the turntable sanding head, the

handle position can be adjusted horizontally

or vertically.

SELECTING THE SANDING PAD

• Always use abrasive pads suited to the

material you want to sand. The pads

must have the correct grain size.

• Depending on grain size there are

degrees of coarseness. The coarseness

is specied by a number on the back of

the pads. (A small number means very

coarse pad. The higher the number is,

the ner the grain.)

• It is important to use the right pad for

each job. For rough sanding use grain

sizes up to 80, for soft wood as larch,

pine or spruce use pads from 120 to 150.

For dense hardwood as beech or maple,

the grain sizes up to 220 can be used.

• Attach the desired sanding pad (5) on the

sanding plate (6). Make sure the

openings of the sanding pad t with the

suction holes (10) on the sanding plate.

Firmly press the sanding pad down on

the sanding plate.

With the provided hook and loop system

the sanding pad can be quickly removed.

Pull off the sanding pad. Place the new

sanding pad and make sure the openings

of the plate and the sanding pad match

together.

MOUNTING THE DUST COLLECTION HOSE

Always use the dust collection hose,

particularly when sanding painted

surfaces.

Attach the dust collection hose (9) to the dust

extraction ange (7) and connect a vacuum

cleaner to the hose.

ON/OFF SWITCH

1. Connect the sander to the power socket.

2. To turn on the machine push the ON/OFF

switch (2) forward, using your thumb. To

turn off the machine, pull the ON/OFF

switch back.

3. Hold the machine rmly with your hand

when using and whenever possible,

move the machine in a steady motion

parallel to the surface. By doing so, you

will avoid grooves or hollows on the

surface.

SANDING

•

Apply only moderate pressure on the

machine. Too much pressure will lead to

jamming of the mechanism and will spoil

the result. Excessive pressure will

overheat the machine.

• Always select abrasive pad with

coarseness suited the condition of the

surface.

• Use ner pads in the consecutive sanding

until the desired smoothness is reached.

If you desire a very smooth nish you

may slightly moisten the surface before

the last sanding. This will slightly swell the

bres and allow a smoother nish.

SPEED REGULATOR

Electronic variable speed

•

The required rotation speed for sanding

depends on the material being processed.

It is best selected by a practical test.

Always use a speed which is high enough

to prevent the machine from stopping due

to overload. The speed can be adjusted

with the speed regulator (3).

• For working with min. speed, turn the

regulator in direction 1. This setting

corresponds to a speed of 6,000

revolutions per minute.

7061488 Ma # 1208-14.indd 12 14-08-12 08:44

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-DSR001 - 7061488 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info