Bedienungsanleitung Batavia BT-JS002 - 7063410 (Seite 9 von 42) (Deutsch, Englisch, Holländisch, Französisch)

758289

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English

6. Contents of packing

1× Pendulum Stroke Jig Saw

2× Saw blade

1× Parallel stop

1× Vacuum hose adapter

1× Allen key

1× Instruction manual

7. Intended use

The jig saw is intended for split cuts and

cutouts in wood, plastic and rubber. The jig

saw can be used for straight and curved

cuts at 0° to 45°.

8. Inserting the saw blade

Always disconnect the main power plug

prior to performing any work on the

machine.

Use only T-shank jig saw blades.

8.1 Lift the transparent blade cover (12) up

and hold it.

8.2 Pull the lever of the blade clamp and

slide the saw blade into the groove as

far as it will go with the blade teeth

pointing forward. Make sure that the lug

of the blade tted into the blade clamp,

then release blade clamp lever (17),

check the blade held rmly.

8.3 Place the transparent blade cover to

initial position.

Attention: After a cut, the saw blade will be

very hot because of the friction. Be careful

when removing the saw blade. Protect your-

self by wearing appropriate protective

gloves.

9. Power on/off

9.1 Insert the mains plug into the socket.

The LED indicator light (14) lights up

and indicates that power is applied.

9.2 To turn on the pendulum stroke jig saw,

press the ON/OFF switch (3). The

switch can be set to continuous mode

by pressing the power on lock (2).

9.3 Pressing the ON/OFF switch (3) again

returns the power on lock (2) to the

starting position.

9.4 To turn off the pendulum stroke jig saw,

release the ON/OFF switch.

10. Startup

Take note of the line voltage. The voltage of

the power source must match the informa-

tion on the type label on the machine.

220 V~ – 240 V~ can also be operated with

230 V~ units.

• Before switching on of the jig saw, the

front of the base plate (8) must lie flat

on the workpiece. Make sure that the

base plate rests securely on the entire

surface.

• Always hold the jig saw rmly with both

hands. Make sure that the saw blade is

not in contact with the workpiece before

the jig saw is turned on.

• Make sure that the saw blade has com-

pletely stopped before removing the jig

saw from the workpiece.

11. Stroke rate selection

You can adjust the stroke rate with the

stroke rate controller (1). The required

stroke rate of the saw blade is dependent on

the material and the saw blade used, and

should be determined by practical tests.

Material Stroke adjustment

Wood . . . . . . . . . . 5 — 6

Soft steel . . . . . . . .

—

Stainless steel. . . . . . . 3 — 4

Aluminium . . . . . . . . 3 — 6

Plastic . . . . . . . . . 1 — 4

Attention: Do not let the jig saw run in con-

tinuous operation with the lowest speed. As

a result, the motor can overheat.

12. The diagonal cut

The mitre angle is variable between 0° and

45°.

7062849-Jig_Saw_800W-Ma-1803-09.indb 7 22-03-18 11:07

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-JS002 - 7063410 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info