Bedienungsanleitung Batavia BT-PD001 - 7062052 (Seite 17 von 36) (Deutsch, Englisch, Holländisch, Französisch)

589461

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

English

HAMMER DRILLING IN CONCRETE OR

BRICK

Caution: Stone drills can get very

hot.

It may be necessary to drill with smaller bits

and re-drill to nominal size so that later the

plug is rmly seated.

For large bores, for instance in very hard

concrete, use a smaller bit for pilot drilling

and re-drill to nominal size.

Do not apply a lot of pressure on the

machine, let the machine do the work, guid-

ing the machine with light pressure is

sucient.

Hold the machine with the auxiliary handle,

the bit can jam, particularly with deep bores,

and the machine will turn.

MAINTENANCE

Take care that the machine is not

connected to power whenever

maintenance work on the

mechanical parts is taking place.

These machines are designed to function

problem-free for a long period with a mini-

mum of maintenance. Through regular

cleaning and correct treatment, you help

assure a long working life for your machine.

Defects

The machine should be regularly inspected

for the following possible defects, and

repaired if necessary.

• Damage to power cord

• Broken on/o trigger assembly.

• Short circuiting.

• Damaged moving parts.

Trouble shooting

1. When switched on, the motor does

not turn

• Failure in power supply.

• Check the power supply.

• Poor contact in the on/o trigger.

• Repair or replace the trigger assembly.

• Mains voltage too low.

• Extension lead too long, or too light.

• Damaged motor.

• Have your machine repaired by an

expert.

• Carbon brushes worn.

• Replace the carbon brushes.

2. Motor generates excessive noise,

and runs too slowly or not at all

• Motor is overloaded due to excessive

pressure or drilling depth.

• Reduce the pressure or drilling depth,

reduce power.

• Damaged motor.

• Have your machine repaired by an

expert.

• Supply voltage too low.

• Adjust the supply voltage.

• Carbon brushes worn.

• Replace the carbon brushes.

3. Overheating in the transmission case

• Overloading of machine, or blunt drill bit

• Reduce the loading, or hone the drill

bit.

• Reduced voltage.

• Adjust the supply voltage.

4. Heavy sparking from the motor

• Inspect the carbon brushes for wear.

Cleaning

Clean the machine casings regularly with a

soft cloth, preferably after each use. Make

sure that the ventilation openings are free of

dust and dirt. Remove very persistent dirt

using a soft cloth moistened with soapsuds.

Do not use any solvents such as gasoline,

alcohol, ammonia, etc. Chemicals such as

these will damage the synthetic

components.

Faults

Should a fault occur, e.g. after wear of a

part, please contact the service address on

the warranty card. Separate you nd an

exploded view showing the parts that can

be ordered.

7062052_Rotary-Hammer_420W_Ma_#1408-11.indb 17 28-08-14 14:37

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia BT-PD001 - 7062052 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info