Bedienungsanleitung Batavia XXL SPEED SAW Mini BT-CS001 (Seite 29 von 64) (Deutsch, Englisch, Holländisch, Französisch)

589451

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

avoid the blade touching the workpiece when

the blade guard is raised to expose the blade

as outlined in instruction.

7. Turn switch ON as outlined on Page 28.

NOTE: Do not proceed any further until the

blade is running at full speed.

8. Using the thumb on your left hand, press the

blade guard release button (6).

9. Gently press downward on the front of the tool

to raise the blade guard until it touches the

depth control stop (9).

10. Re-check the alignment of the front cut line

indicator (7) and the cutting line marked on the

workpiece (8).

11. Slowly move the tool forward until the blade

touches the workpiece and begins to cut at the

cutting line. NOTE: Feed the blade into the

workpiece at a slow steady pace. Do not force

the tool so the motor slows down. The red

“overload” light (10) will illuminate if the motor

is being overloaded. The blade will cut faster

and cleaner when turning at full speed.

Warning! Never try to cut a curve. This

tool is designed only for straight line

cuts. Attempting to cut curves will

damage the blade, make rough cuts and

possible break the blade. Serious injury

may result.

When the cut is completed, release the ON/OFF

switch and wait for the blade to come to a complete

stop before removing the tool from the workpiece.

Warning! Make sure the blade guard

returns to its normal position

covering the blade before taking your

hands off the tool.

6.12 Cutting (with edge guide)

To cut using the edge guide, follow the same basic

principles as noted in Paragraphs 1 through 11

above. Instead of following a cutting line, you will

simply set the edge guide at the appropriate width

and hold the guide shoe (1) against the edge of the

workpiece (2) to guide the blade in a straight line.

6.11 Cutting (without edge guide)

Warning! Always use two hands on

the tool when cutting. This will make

operation of the tool easier and

promote maximum safety.

1. Install appropriate cutting blade in the tool.

2. Adjust cutting depth as outlined on Page 27.

3. Plug the tool cord into the power source.

NOTE: The green “power on” light (1) on the

right hand side of the tool will illuminate when

power is “live”.

4. Place leading edge of the blade guard (2) on

the workpiece to be cut.

5. Grasp the tool with two hands. Place your right

hand on the body of the tool (3) being careful

not to cover the motor vents (4). Place your

left hand on the forward part of the tool (5) so

your thumb can operate the blade guard

release button (6).

6. Line up front cut line indicator (7) with the

cutting line marked on the workpiece (8).

NOTE: Do not place the blade guard too far

forward on the workpiece. This is important to

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavia XXL SPEED SAW Mini BT-CS001 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Batavia XXL SPEED SAW Mini BT-CS001

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info