Bedienungsanleitung Batavus Isola E-go (Seite 28 von 83) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

779539

Zoom out

Zoom in

Vorherige Seite

1/83

Nächste Seite

English–4

Bosch eBike Systems 0 276 001 SAI | (14.8.13)

Switching the Push-assistance mode On/Off

The push-assistance feature makes it easier to push the

eBike. The speed in this function depends on the set gear and

cannot exceed 6 km/h (max.). The lower the set gear, the low-

er the speed in the push-assistance function (at full output).

fThe push-assistance function may only be used when

pushing the eBike. Danger of injury when the wheels of

the eBike do not have ground contact while using the push-

assistance function.

To activate the push-assistance function, press and hold the

“WALK” button 14 on the operating unit. The eBike's drive is

activated.

The push-assistance function is switched off as soon as any

of the following incidents occur:

– You release the “WALK” button 14,

– The wheels of the eBike are blocked (e. g., through braking

or running against an obstruction),

– Your speed exceeds 6 km/h.

Back-pedalling function (optional)

For bikes with back-pedalling function, the pedals rotate

when the push aid is switched on. If the rotating pedals are

blocked, the push aid switches off.

Switching the Lighting On/Off

In the version in which the driving light is powered via the

eBike system, you can use the 2 button on the HMI to simulta-

neously switch the front light and rear light on and off.

When the lighting is switched on “Lights on” appears and

when the lighting is switched off “Lights off” appears for ap-

prox. 1 s in the text indication d. The illumination symbol c is

displayed when the light is on.

Switching the driving light on and off has no effect on the back

lighting of the display. The back lighting of the display is active

as soon as the system or the display is switched on.

Speed and Distance Indication

The speed indication f always displays the current speed.

The following functions are available in the function indica-

tion (combination of text indication d and value indication e):

–“Range”: Estimated range of the available battery-pack

charge (for constant conditions such as assistance level,

route profile, etc.)

–“Distance”: Distance covered since the last reset

–“Trip time”: Trip time since the last reset

–“Avg. Speed”: Average speed achieved since the last reset

–“Max. Speed”: Maximum speed achieved since the last

reset

–“Clock”: Current time

–“odometer”: Display of the total distance travelled with

the eBike (not resettable)

To switch between the indication functions, press the “i”

button 1 on the HMI or the “i” button 11 on the operating unit

until the desired function is displayed.

To reset “Distance”, “Trip time” and “Avg. Speed”, switch

to any of the three functions and then press and hold the

“RESET” button 6 until the indication is set to zero. This also

resets the values of the other two functions.

To reset the “Max. Speed”, switch to this function and then

press and hold the “RESET” button 6 until the indication is set

to zero.

To reset “Range”, switch to this function and then press the

“RESET” 6 button until the display is reset to the value of the

factory setting.

When the HMI is removed from the holder 4, all function val-

ues remain stored and can be viewed.

Displaying/Adapting Basic Settings

The basic settings can be displayed and changed no matter if

the HMI is in the holder 4 or not.

To access the basic settings menu, press and hold the

“RESET” button 6 and the “i” button 1 until “Configuration”

is displayed in text indication d.

To switch between the basic settings, press the “i” button

1 on the HMI until the desired basic setting is displayed. When

the HMI is inserted in holder 4, you can also press the “i” but-

ton 11 on the operating unit.

To change the basic settings, press the On/Off button 5 next

to the “–” indication to decrease the value or scroll down, or

the illumination button 2 next to the “+” indication to increase

the value or scroll up.

When the HMI is inserted in holder 4, you can also change the

values with the “–” button 12 or the “+” button 13 on the op-

erating unit.

To exit the function and store a changed setting, press the

“RESET” button 6 for 3 s.

The following basic settings are available:

–“unit km/mi”: The speed and distance can be displayed

either in kilometres or miles.

–“time format”: The time can be displayed either in the

12 hour or 24 hour format.

–“clock”: The current time can be set here. Pressing and

holding the setting buttons fast-forwards the setting

speed.

–“English”: The language for text indication can be

changed. The available languages are German, English,

French, Spanish, Italian and Dutch.

–“power-on hours”: Indicates the total travel duration with

the eBike (not changeable).

–“wheel circum.”: You can change this value pre-set by the

manufacturer by ±5%.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavus Isola E-go Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info