Bedienungsanleitung Batavus X4 (Seite 12 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

623733

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

OWNER'S MANUAL

•

BATAVUS

•

Press the Plus/Minus buttons to select the User

program.

•

Press the Mode button.

The first profile bar will blink.

•

Use the Plus/Minus buttons to adjust the

resistance (level 1 -- 6).

•

Press the Mode button.

The second bar will blink.

Continue in this manner until all 20 bars are set.

If you do not wish to make any more entries (e.g.,

time), then press the Start button. To enter data,

press the Start button again. The time will blink

on Display 2. Now enter the desired data and then

press the Start button to begin training.

ADDITIONAL NOTES:

1) The control panel of your cross trainer

is protected against incorrect operation.

Consequently, pushing the wrong button does not

create any problems. If you enter something that is

wrong or not possible, a signal sounds.

2) If you start training without entering values, all

values are displayed counting from zero upward.

3) If E-2 is shown on the display, something is

wrong with the connection to the magnetic brake.

Wait for 10 seconds. After this, you may have to

press the Total Reset button.

4) If you press the Total Reset button after training,

the data for this training session will not be stored.

5) If you preset data and then switch to another

program, these data will be saved if you do not

change anything.

6) Watts are displayed in all programs. However,

the resistance is only automatically controlled in

accordance with the previous inputs in the Watt

programs.

7) If you have preset values, for example, time,

distance or calories, the control panel stops when

any one function reaches zero. If you then press the

Start button, the control panel starts again using

the previous data.

8) In the Fitness program, it is not possible to

preset training values because this program only

uses your personal data.

9) If you enter an upper pulse rate (e.g., 130),

a signal sounds during training if the limit

is exceeded. This is so that you do not train

unintentionally at an excessive pulse rate.

10) If the control panel is in Sleep mode and you

begin pedaling, the last program used is displayed.

11) The actual pulse rate is displayed if you use the

hand pulse sensors, the ear clip or the chest strap.

12) Training with preset time and program profiles.

The preset time is distributed over the 20 profile

bars. Example: 20 minutes over 20 profile bars

corresponds to 1 minute until a switch is made to

the next bar.

13) Programs that require a USB stick with

personal data cannot be accessed without a USB

stick being inserted. They do not appear on the

display, for example, the H.R.C.

14) Following a training interruption where

the control panel enters the Sleep mode, you

may continue training using the existing values

(exception: Fitness test). To do this, press the Start

button or start pedaling.

15) Before the control panel can display the pulse

rate, it needs several seconds for calculation

purposes. Doing this, of course, requires a pulse

measurement using the hand pulse sensors, the ear

clip or the chest strap.

16) The pushbuttons on the rigid handgrip have

the same function as the Plus/Minus buttons.

17) In this unit, energy consumption is calculated

based on average values. However, as each

person has different capabilities for producing

energy (known as efficiency), the energy

consumption displayed can, by necessity, only

be an approximation of the actual consumption

and cannot be used for therapeutic purposes. The

energy consumption during a training session is

displayed in kcal (kilocalories). To convert this into

joules, use this formula: 1 kcal = 4.187 kJ.

18) Your cross trainer also has an odometer

function. The total distance of all training sessions

is shown briefly on Display 1 when you plug the

unit in or if the Total Reset button is pressed.

19) Example: ODO 15 K = 15 kilometers total

distance.

TRANSPORT AND STORAGE

Please follow these instructions when carrying

and moving the equipment about, because lifting

it incorrectly may strain your back or risk other

accidents:

The device is easy to move by pushing along on the

integrated transport wheels. Tilt the device from

the front and push along the floor on the wheels at

the front support. We recommend that you use a

protective base when transporting the equipment.

To prevent the equipment malfunctioning, store in

a dry place with as little temperature variation as

possible and protected from dust.

MAINTENANCE

The equipment requires very little maintenance.

Check, however, from time-to-time that all screws

and nuts are tight.

•

After exercising, clean the equipment with a soft,

absorbent cloth. Do not use solvents. Sweat may

cause corrosion: we recommend therefore that you

protect all metal surfaces outside the plastic covers

with teflon.

batavusX4.indd 12batavusX4.indd 12 12.10.2005 12:49:4112.10.2005 12:49:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Batavus X4 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info