Bedienungsanleitung Bauknecht B7F HS51 X (Seite 4 von 6) (Englisch)

806734

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

LOADING THE RACKS

CLEANING THE FILTER ASSEMBLY

Regularly clean the lter assembly so that the lters do not clog and that

the waste water ows away correctly.

Using the dishwasher with clogged lters or foreign objects inside the l-

tration system or spray arms may cause unit malfunction resulting in loss of

performance, noisy work or higher resources usage.

The lter assembly consists of three lters which remove food residues

from the washing water and then recirculate the water.

The dishwasher must not be used without lters or if the lter is loose.

At least once per month or after every 30 cycles, check the lter assembly

and if necessary clean it thoroughly under running water, using a non-me-

tallic brush and following the instructions below:

1. Turn the cylindrical lter A in an anti-clockwise direction and pull it out

(Fig 1). It is important when reinstalling the lter that the two trian-

gles shown on the zoom meet.

2. Remove the cup lter B by exerting a slight pressure on the side aps

(Fig 2).

3. Slide out the stainless-steel plate lter C (Fig 3).

4. In case you nd foreign objects (such as broken glass, porcelain, bones,

fruit seeds etc.) please remove them carefully.

5. Inspect the trap and remove any food residues. NEVER REMOVE the

wash-cycle pump protection (shown by an arrow) (Fig 4).

After cleaning the lters, replace the lter assembly and x it in position

correctly; this is essential for maintaining the ecient operation of the dish-

washer.

CAPACITY: 15 standard place-settings

CARE AND MAINTENANCE

CUTLERY RACK

The third rack was designed to house the cut-

lery.

Arrange the cutlery as shown in the gure.

A separate arrangement of the cutlery makes col-

lection easier after washing and improves wash-

ing and drying performance.

Knives and other utensils with sharp edges

must be positioned with the blades facing

downwards.

The cutlery rack is equipped with two sliding

side trays to make the most of the height of the

space below and enable the loading of high

items into the upper rack.

UPPER RACK

Load delicate and light dishes: glasses, cups,

saucers, low salad bowls.

The upper rack has tip-up supports which can

be used in a vertical position when arranging

tea/ dessert saucers or in a lower position to

load bowls and food containers.

(loading example for the upper rack)

Adjusting the height of the upper rack

The height of the upper rack can be adjusted: a high position to place bulky

crockery in the lower basket and low position to make the most of the tip-up

supports by creating more space upwards and avoiding collision with the

items loaded into the lower rack.

The upper rack is equipped with an Upper Rack height

adjuster (see gure), without pressing the levers, lift it

up by simply holding the rack sides, as soon as the rack is

stable in its upper position. To restore to the lower posi-

tion, press the levers A at the sides of the rack and move

the basket downwards.

We strongly recommend that you do not adjust the

height of the rack when it is loaded.

NEVER raise or lower the basket on one side only.

Foldable aps with adjustable position

The side foldable aps can be folded or unfolded

to optimize the arrangement of crockery inside

the rack. Wine glasses can be placed safely in

the foldable aps by inserting the stem of each

glass into the corresponding slots.

Depending on the model:

• to unfold the ap there is needed to slide it up

and rotate or release it from the snaps and pull

it down.

• to fold the ap there is needed to rotate it and

slide ap down or pull it up and attach ap to

the snaps.

LOWER RACK

For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids should

ideally be placed at the sides to avoid interferences with the spray arm.

The lower rack has tip-up supports which can be used in a vertical position

when arranging plates or in a horizontal position (lower) to load pans and

salad bowls easily.

(loading example for the lower rack)

POWER CLEAN®

Power Clean® uses the special water jets in

the rear of the cavity to wash more intensive-

ly the highly dirty items. The lower rack has

a Space Zone, special pull-out support in the

rear of the rack that can be used to support

frying pans or baking pans in an upright po-

sition, thus taking up less space.

Placing the pots/casseroles faced to the

Power Clean® component please activate

the POWER CLEAN® on the panel.

How to use the Power Clean®:

1. Adjust the Power Clean® area G folding

down the rear plate holders to load pots.

2. Load pots and casseroles inclined verti-

cally in the Power Clean® area. Pots have

to be inclined towards the powerful water

jets.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht B7F HS51 X Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht B7F HS51 X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info