806458

Bauknecht B7I HT58 TC Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
EN
6
Policies, standard documentation, ordering of spare parts and additional product information can be
found by:
• Using QR code and visiting our website: docs.bauknecht.eu
• Visiting our website: parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting
our After-sales Service, please state the codes provided on your product’s identication plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes
the model identier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu
IEC 436
:
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher does
not ll the water.
The display shows:
H2O and is
lit; acoustic alarm
sounds.
No water in the water supply or the tap is closed. Make sure there is water in the water supply and the water tap is open.
The water inlet hose is kinked. Check the inlet hose (see INSTALLATION). Open dishwasher door, press START/Pause button and
close the door within 4 seconds.
The screen in the water inlet hose is clogged; it is
necessary to clean it. Check and clean the screen in the water inlet hose. Open dishwasher door, press START/Pause
button and close the door within 4 seconds.
The dishwasher
nishes the cycle
prematurely.
The display shows:
F8 E3
The lter is clogged with food residues or lime-
scale. Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and DESCALE
INSTRUCTION).
Drain hose positioned too low or siphoning into
the home sewage system.
Check if the end of the drain hose is placed at the correct height (see INSTALLATION). Check for
siphoning into the home sewage system, and install a siphon breaker/air admittance valve if
necessary.
An excessive amount of foam is present. The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER).
Air in the water supply. Check water supply for leaks or other issues letting air inside.
The dishes are not
dried well.
Rinse aid is not present or the dosage is too low. Make sure the rinse aid dispenser is lled (see FILLING THE RINSE AID DISPENSER). Multifunctional
tablets only will not provide as good drying eects as the actual use of liquid rinse aid.
The dishes have been unloaded after the door
was opened automatically but before the actual
cycle end.
Make sure the cycle has ended before starting to unload the dishes (see DAILY USE). For even
better drying results, it is recommended to let the dishes sit inside the dishwasher with the door
open for additional 15 minutes after the cycle ends.
The dishes are sitting too at. If you notice puddles of water inside cavities of cups, mugs or bowls, try loading the dishes
(especially in the upper rack) providing more inclination to let larger amounts of water drip
down before drying starts.
The selected cycle does not have the drying
phase.
Please check in the PROGRAMS TABLE if the selected program is equipped in the drying phase. A
cycle without the drying phase may not deliver desired drying eciency, so it is recommended
to change cycle selection for the one that has the drying phase.
The dishes are made of non-stick or plastic. Some water drops remaining on this type of material are normal.
Dishes and glasses
have blue streaks
or bluish tinges. Rinse aid dosage is excessive. Adjust the dosage to a lower setting.
Dishes and glasses
are covered with li-
mescale or a whitish
lm.
The salt reservoir is empty. Rell the reservoir with salt as soon as possible. Using the appliance without salt may cause
damage to its internal components.
The water hardness setting is too low.
Increase the setting (see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly closed. Check and close the salt reservoir cap.
The rinse aid reservoir is empty or the rinse aid
dosage is insucient. Rell the dispenser with rinse aid and check the dosage setting (for more information
- see FILLING THE RINSE AID DISPENSER).
The dishwasher
shows F8 E5 Valve is blocked or faulty. Close the water tap, if possible. Do not switch o the power supply. Call the service.
… 6 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bauknecht B7I HT58 TC wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info