Bedienungsanleitung Bauknecht B8I HF58 TUSC (Seite 5 von 28) (Deutsch, Englisch, Holländisch, Französisch)

806456

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENDaily Reference Guide

CLEANING THE SPRAY ARMS On occasions, food residue

may become encrusted onto

the spray arms and block the

holes used to spray the wa-

ter. It is therefore recommen-

ded that you check the arms

from time to time and clean

them with a small non-me-

tallic brush.

To remove the upper spray

you must remove it together

with the manifold.

The Top Rack has a xed wash tube with all the wash nozzles facing upward.

To clean it you can slide the rack out and with a tweezer remove items that

may be lodged in the nozzles.

The lower spray arm may be removed

by pulling it upwards and rotating it

anti-clockwise. Mounting back the

spray arm is by pulling it down and

rotating it clockwise.

The top spray arm may be removed

by pressing it up and then rotating it

anti-clockwise. Mounting back the

spray arm is by pulling it upwards and

rotating it clockwise.

TROUBLESHOOTING

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.

For other errors or issues please contact authorized After-sales Service whose contact details can be found in the warranty booklet.

Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specic Regulation requirements.

PROBLEMS POSSIBLE CAUSES SOLUTIONS

The salt indicator

is lit Salt reservoir is almost empty. Rell the reservoir with salt (for more information - see FILLING THE SALT RESERVOIR). Check the

water hardness setting if necessary (see WATER HARDNESS TABLE).

The salt indicator

is blinking Salt reservoir is empty. Rell the reservoir with salt as soon as possible. Using the appliance without salt may cause

damage to its internal components.

The rinse aid

indicator is lit

or blinking

Rinse aid dispenser is empty. (After rell the rinse

aid indicator may remain lit for a short time). Rell the dispenser with rinse aid (for more information - see FILLING THE RINSE AID DISPENSER).

Descale indicator

is lit or blinking;"dES"

alarm is displayed.

Limescale is accumulating on internal components

of the appliance.

Descale the appliance immediately using the Self Clean program and a commercially available

descaling product (see OPTIONS AND FUNCTIONS). Rell the reservoir with salt. Check the water

hardness setting. If the appliance is not descaled, it will stop functioning.

The dishwasher

won’t start or does

not respond to

commands.

The appliance has not been plugged in properly. Insert the plug into the socket.

Power outage. For safety reasons, the dishwasher will not restart automatically when power returns.

Open dishwasher door, press START/Pause button and close the door within 4 seconds.

The dishwasher door is not closed.

ActiveDry pin is not pulled in. Vigorously push the door until you hear the “click”.

A cycle is interrupted by door opening for more

than 4 seconds. Press START/Pause and close the door within 4 seconds.

The control panel does not respond or F6 E1 is

displayed.

Switch o the appliance by pressing the ON-OFF/Reset button, switch it back on after approxi-

mately one minute and restart the program. If the problem persists, unplug the appliance for 1

minute, then plug it back in.

The dishwasher

won’t drain.

Display shows:

F7 E3 or F9 E1

The lter is clogged with food residues or lime-

scale Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and DESCALE

INSTRUCTION).

The drain hose is kinked. Check the drain hose (see INSTALLATION INSTRUCTION).

The sink drain pipe is blocked. Clean the sink drain pipe.

The dishwasher ma-

kes excessive noise.

Dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam is present.

The detergent has not been measured out correctly or it is not suitable for use in dishwashers

(see FILLING THE DETERGENT DISPENSER). Restart the current cycle by switching OFF the dishwa-

sher, then switch it on again, select a new program, press START/Pause and close the door within

4 seconds. Please do not add any detergent.

Crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).

The lter is clogged with food residues or limescale. Clean the lter assembly (see CARE AND MAINTENANCE).

The dishes are not

clean.

Crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).

Spray arms cannot rotate freely, being hindered

by the dishes. Arrange the crockery correctly (see LOADING THE RACKS). Check that the upper rack is in the

correct position and adjust (lift up) if necessary.

The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).

An excessive amount of foam is present.

The detergent has not been measured out correctly or it is not suitable for use in dishwashers (see

FILLING THE DETERGENT DISPENSER).

The cap on the rinse aid compartment has not

been closed correctly. Make sure the cap of the rinse aid dispenser is closed.

The lter is clogged with food residues or limescale. Clean the lter and descale the appliance (see CLEANING THE FILTER ASSEMBLY).

The salt reservoir is empty. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

Bauknecht B8I HF58 TUSC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info