Bedienungsanleitung Bauknecht BCIO 3O41 PLET S (Seite 4 von 8) (Englisch)

806774

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

OPTIONS AND FUNCTIONS

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).

If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED ashes rapidly 3 times

and beeps will sound. The option will not be enabled.

MULTIZONE

If there are not many dishes to be washed, a half loading may

be used in order to save water, electricity and detergent.

Select the program and then press the MULTIZONE button:

the symbol of the chosen rack will appear on the display. By

default the appliance washes dishes in all racks.

To wash only the specic rack, press this button repeatedly:

shown on the display (only lower rack)

shown on the display (only upper rack)

shown on the display (only cutlery rack)

shown on the display (option is OFF and the appliance will

wash dishes in all racks).

Remember to load the upper or lower rack only, and to

reduce the amount of detergent accordingly.

If upper rack is removed, please apply detergent directly

to tub instead of detergent dispenser.

TABLET (Tab)

This setting allows you to optimize the performance of the

program according to the type of detergent used.

Press the START/PAUSE button for 3 seconds (the correspon-

ding symbol will light up) if you use combined detergents in

tablet form (rinse aid, salt and detergent in 1 dose).

If you use powder or liquid detergent, this option should

be o.

POWER CLEAN®

Thanks to the additional power jets this option provides

a more intensive and powerful wash in the lower rack, in the

specic area. This option is recommended for washing pots

and casseroles. Press this button to activate POWER CLEAN

(the indicator lights up).

TURBO

This option can be used to reduce the duration of the main

programs while maintaining the same washing and drying

performance levels.

After selecting the program, press the TURBO button and the

indicator light will switch on. To deselect the option, press the

same button again.

DELAY

The start time of the program may be delayed for a period of

time between 1 and 12 hours.

1. Press the DELAY button: the corresponding «h» symbol

appears on the display; each time you press the button,

the time (1h, 2h, etc. up to max. 12h) from the start of the

selected wash cycle will be increased.

2. Select the wash program, press the START/PAUSE button

and within 4 seconds close the door: the timer will begin

counting down.

3. Once this time has elapsed, the indicator light «h» switches

o and the wash cycle begins.

To adjust the delay time and select a shorter period of

time, press the DELAY button. To cancel it, press the button

repeatedly until the selected delayed start indicator light «h»

switches o.

The DELAY function cannot be set once a wash cycle has

been started.

OPERATION INDICATOR

A LED light projected on the oor indicates that the dishwasher is

working. One of the following operating modes can be selected:

a) Disabled function.

b) When the cycle starts the light goes on for few seconds,

stays o during the cycle and ashes at the end of the cycle.

c) The light stays on during the cycle and ashes at the end of

the cycle (default mode).

If the delayed start was set, the light goes on either for the rst

few seconds or the entire duration of the countdown, based

on whether mode b) or c) was set.

The light goes o every time the door is opened. To select the

mode you prefer, switch on the machine, hold down button

P until one of the three letters appears on the display, press

button P until you reach the desired letter (or mode), hold

down button P to conrm the selection.

Note: If ActiveDry is active and it opens the door, then

Operation Indicator will not ash at the end of cycle.

ActiveDry

ActiveDry is a convection drying system which automatically opens

the door during/after drying phase to ensure exceptional drying per-

formance every day. Door opens at the temperature that is safe to your

kitchen furniture, thus door will not be opened when the option of

TURBO is on.

As additional steam protection, special designed protection foil is added

together with the dishwasher. To see how to mount protection foil

please refer to (INSTALLATION GUIDE).

ActiveDry functionality could be disabled by the user as follows:

1. Go to the Dishwasher software menu pressing and holding P

button (6 sec).

2. You are currently in Light Control Menu (please refer to OPERATION

INDICATOR description), if you don’t want to change anything

please press and hold P button (

until one of the two letters appears

on the display).

3. You switched to ActiveDry Control Menu, you could change status

of ActiveDry functionality by pressing P button:

E – enabled d – disabled

To conrm the change and exit from the Control Menu please press and

hold P button (3 sec).

INTERNAL LIGHTS

When the feature is active the LEDs in the tub are automatically switched

on/o as soon as the user open/close the door respectively.

If the door remains opened for more than 10 min, the LEDs in the tub

switch o (to turn them on again, the door has to be closed and opened

again).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht BCIO 3O41 PLET S Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht BCIO 3O41 PLET S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info