Bedienungsanleitung Bauknecht BUO 3O41 PLT X (Seite 8 von 8) (Englisch)

806718

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.

For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.

The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.

TROUBLESHOOTING

PROBLEMS POSSIBLE CAUSES SOLUTIONS

Salt

indicator is lit

Salt reservoir is empty (after rell the salt indicator may

remain lit for several wash cycles).

Rell reservoir with salt (for more information - see page 2).

Adjust water hardness (see table, page 2).

Rinse aid

indicator is lit

Rinse aid dispenser is empty (after rell the rinse aid

indicator may remain lit for several wash cycles). Rell dispenser with rinse aid (for more information - see page 2).

The dishwasher

won’t start or does

not respond to

commands.

The appliance has not been plugged in properly. Insert the plug into the socket.

Power outage. For safety reasons, dishwasher will not restart automatically when power returns.

Press the START/Pause button to resume the cycle.

The dishwasher door is not closed.

ActiveDry pin is not pulled in. Vigorously push the door until you hear the “click”.

Cycle is interupted by door opening for > 4 sec.

Close the door and press START/Pause button.

It does not respond to commands. Display shows:

F9 or F12 and both On/O

and START/Pause LEDs are blinking rapidly.

Switch o the appliance by pressing the ON/OFF button, switch it back on after

approximately one minute and restart the program. If problem persists, unplug the

appliance for 1 minute, then plug it back in.

The dishwasher

won’t drain.

Display shows: F3

and both On/O and

START/Pause LEDs

are blinking rapidly.

The wash cycle has not nished yet. Wait until the wash cycle nishes.

The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).

The sink drain pipe is blocked. Clean the sink drain pipe.

The lter is clogged up with food residues. Clean the lter (see CLEANING THE FILTER ASSEMBLY).

The dishwasher

makes

excessive noise.

The dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has been produced.

The detergent has not been measured out correctly or it is not suitable for use in

dishwashers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by pressing

the DRAIN button (see OPTIONS AND FUNCTIONS) and run new program without

detergent.

The dishes are not

clean. The crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).

The spray arms cannot rotate freely, being hindered

by the dishes. Arrange the crockery correctly (see LOADING THE RACKS).

The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).

An excessive amount of foam has been produced.

The detergent has not been measured out correctly or it is not suitable for use in

dishwashers (see FILLING THE DETERGENT DISPENSER).

The cap on the rinse aid compartment has not been

shut correctly. Make sure the cap of the rinse aid dispenser is closed.

The lter is soiled or clogged. Clean the lter assembly (see CARE AND MAINTENANCE).

There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

The dishwasher does

not ll the water.

Display shows:

and F6, both On/O

and START/Pause

LEDs are blinking

rapidly.

No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.

The inlet hose is bent. Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher

and reboot.

The sieve in the water inlet hose is clogged; it is

necessary to clean it.

After having carried out the verication and cleaning, turn o and turn on the

dishwasher and restart a new program.

Dishwasher nishes

the cycle prematurely.

Display shows: F15

and both On/O and

START/Pause LEDs

are blinking rapidly.

Drain hose positioned too low or siphoning into

home sewage system.

Check if end of drain hose is placed at correct height (see INSTALLATION).Check for

siphoning into home sewage system, install air admittance valve if necessary.

Air in water supply. Check water supply for leaks or other issues letting air inside.

400011477172

06/2020 as - Xerox Fabriano

Policy and standard documentation and additional product information can be found by:

• Visiting our website docs.bauknecht.eu

• Using QR Code

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).

When contacting our After-sales Service, please state the codes provided on your product‘s

identication plate.

The model information can be retrieved using the QR-Code reported in the energy label.

The label also includes the model identier that can be used to consult the portal of the registry

at https://eprel.ec.europa.eu (available only on certain models).

IEC 436

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht BUO 3O41 PLT X Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht BUO 3O41 PLT X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info