Bedienungsanleitung Bauknecht Excellence 4470 (Seite 2 von 2) (Englisch)

560998

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 401 05575

Load your laundry, close the door properly and add detergent as

indicated on the front page and as described in the chapter “Detergent

and Additives” in your Instructions for Use.

1. Turn the programme selector to the desired programme.

The display shows the programme duration in hours and

minutes as well as the predefined temperature. The “Start

(Pause)” button blinks.

2. The temperature can be altered by pressing the

“Temperature” button.

3. The indication lamp of the predefined spin speed lights up. In

case you want to set another spin speed, press the “Spin

speed” button .

Push the button of any option desired - the respective indication

lights up.

When the combination of programme and option is not possible,

the light switches off automatically. Unsuitable combinations of

options are deselected automatically.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing and prevent

colours from changing.

• It is particularly useful if you want to postpone spinning to a

later time, or if you want to drain only.

• If you select “Rinse hold”, do not leave the laundry to soak in

the rinse hold for too long.

• The programme stops to “Rinse hold” when the “Rinse hold”

indication in the programme sequence indication lights;

the “Start (Pause)” button blinks.

To terminate the “Rinse hold”:

• If you want to drain only without spinning: Press the “Start

(Pause)” button to start the drain process.

• If you want to spin your laundry: Press the “Spin speed” button

to select the desired spin speed and then “Start

(Pause)” to start the spin cycle.

“Prewash” button

• Adds a prewash cycle to the wash programme selected;

prolongs the programme by about a quarter of an hour.

• Recommended for heavily soiled laundry (e.g. containing sand

or granular dirt).

• Do not use liquid detergent for the main wash when activating

the Prewash option.

“Clean +” button

• Choose this option if you use an in-wash additive for stain removal

(powder, for example “Vanish”) - it will optimize the additive’s

efficiency to get better wash performance and stain removal.

• Use with maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together with

your detergent (only use powder detergent with this option).

Respect the manufacturer’s dosing instructions.

• May prolong the programme by up to 15 minutes.

• Appropriate for use of stain removers and bleaches on oxygen

basis. Chlorine or perborate bleaches must not be used!

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very soft

water, washing baby linen and helping people with allergies.

“Easy ironing” button

• Reduces creasing by an increased water quantity and a very gentle spin.

CONSUMPTION DATA

Programme

Te m p e r a t u r e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

without “Rapid” with “Rapid”

Mixed 40 6.0 67 0.58 1:00 —

Cotton 95 7.0 75** 2.40 2:20 —

Cotton* 60 7.0 54 0.80 4:00 2:20

Cotton* 60 3.5 43 0.72 3:00

Cotton 40 7.0 69 0.72 3:00 2:05

Cotton* 40 3.5 46 0.62 2:45

Synthetics 60 3.5 48** 0.95 1:55 1:14

Synthetics 40 3.5 45 0.53 1:40 0:59

Delicates 30 2.5 60 0.40 0:45 —

Wool/Handwash 40 2.0 49 0.63 0:40 —

White 40 7.0 69 0.70 2:20 —

Light colours 40 5.5 70 0.50 1:20 —

Dark 40 5.0 45 0.50 1:40 1:15

Super Silent 60 7.0 69 0.84 4:00 —

AquaEco 40 3.0 19 0.45 1:00 —

Speed 15 30 3.0 30 0.20 0:15 —

Jeans 40 6.0 65 0:55 1:30 1:15

Big Items 40 3.0 74 0.75 1:30 —

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the

values in the table in relation to the water supply pressure and temperature, the load and the type of wash. Water and energy consumption refer to the default setting of

the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

* Reference programmes for Energy Label.

** To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.

*** Automatic adaptation of programme duration after detection of wash load.

***

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“Rapid” button

• Enables quicker washing by shortening the programme duration.

• Recommendable for only lightly soiled laundry.

• Not selectable for Cotton 70 - 95°C.

“Spin speed” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If you select spin speed “0”, the final spinning is cancelled, and

the water is drained only. However, intermediate spin phases

remain during the rinse.

The “Start delay” allows to run the machine at the consumer’s

convenience, for example at night when electricity is cheaper. Do

not use liquid detergent when activating the “Start delay”.

• Select programme, temperature and options.

• Press the “Start delay” button to select a delay time up to 23

hours. The light of the “Start (Pause)” button blinks.

• Press the “Start (Pause)” button . The countdown of the

delay time begins. The light of the “Start (Pause)” button

is on. The light of the start delay button will keep blinking

until the programme starts.

• As soon as the programme starts, the start delay on the display

is replaced by the remaining programme time, and the light of

the “Start delay” button goes off.

• Once having pressed the “Start (Pause)” button , the

number of hours preselected can be changed by pressing and

holding the “Start delay” button.

To cancel the “Start delay”

...before you press “Start (Pause)” :

• Turn the programme selector to another position, or briefly

press the “Reset/Drain” button .

...after having pressed “Start (Pause)” :

• Press “Start (Pause)” - the delay time disappears from

the display. Press “Start (Pause)” again to start the

selected programme immediately.

Open the tap and press “Start (Pause)” . The light stops

blinking and is on. The programme sequence indicator shows the

current programme phase, running from left to right through

Wash, Rinse, Spin/Drain.

The display shows the remaining programme time. Due to

variations in load and temperature of inlet water, the remaining

time is newly calculated in certain programme phases. If this is the

case, an animation appears on the display.

Activating the child lock prevents children from starting a wash

cycle or changing the settings of a running programme. The child

lock cannot be activated or deactivated when the programme

selector is in the “Off/O” position. To activate the child lock:

• Turn the programme selector to a programme position, or run

a programme as usual.

• Press the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds. A key-like symbol will shortly

appear on the display to indicate that the child lock is active.

Any time you try to change a programme setting with active child

lock, the display will briefly show the key-like symbol. The

programme setting cannot be changed anymore. The only change

possible is to switch the washer off by turning the programme

selector to the “Off/O” position. To deactivate the child lock:

• Press again the 2 buttons marked with the key symbol

simultaneously for at least 3 seconds.

If there is a programme setting which you use frequently, the

appliance offers the possibility to save one setting for each

programme so that it can be used again by just pushing one button.

• Select the desired programme, temperature, spin speed and

option(s), push and hold the “Favourites” button for at

least 3 seconds. The “Favourites” indication briefly blinks

and then lights up - the programme setting is saved.

Next time you want to use your individual programme setting,

select the the programme, briefly push the “Favourites” button

and start by pushing “Start (Pause)” .

If you want to replace the saved programme setting by another

one, proceed as already described above.

Before starting and after end of a programme, the lamp lights to show

that the door can be opened. As long as a wash programme is running,

the door remains locked and must on no account be forced open. In

case you have an urgent need to open it during a running programme,

refer to “Reset a running programme before the end”.

If one of the failure indications lights up, refer to the

“Troubleshooting Guide” in your “Instructions for Use”.

In case you used too much detergent, a small vertical bar will light

next to the overdosage symbol on the right of the display when

the wash programme is finished; use less detergent next time. Too

much foam by detergent overdosing can also lead to interruption

of a wash cycle; in this case the display shows “Fod” - follow the

recommendations in the “Troubleshooting Guide” in your

Instructions for Use to solve the problem.

• The display shows “End” and the “Door open” indication lights.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press “Start (Pause)” to pause the programme. The

light blinks.

2. Select the new programme, temperature, any options and

another spin speed if you want.

3. Press “Start (Pause)” again. The light is on, and the

programme continues at the same position where the

previous programme was interrupted. Do not add detergent

for this programme.

The “Reset/Drain” button cancels a programme before

the end.

•Press the “Reset/Drain” button for at least 3

seconds. “rES” appears on the display. The water is drained

out; it may last a while until you can open the door.

START DELAY

PROGRAMME START

CHILD LOCK

SAVE YOUR FAVOURITE PROGRAMMES

“DOOR OPEN” INDICATION

FAILURE INDICATIONS

DETERGENT OVERDOSAGE INDICATION

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

40105575GB.fm Page 2 Friday, May 27, 2011 11:50 AM

Black process 45,0° 150,0 LPI

Bauknecht Excellence 4470 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht Excellence 4470

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info