Bedienungsanleitung Bauknecht Excellence 7210 (Seite 3 von 6) (Englisch)

560989

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

HOW TO PROCEED IF…

...you want to check the dryer yourself first: (If your machine is not functioning correctly, please check the following

points before calling the customer service – also refer to relevant chapter in the Instructions for use)

Drying takes too long /

Laundry is not dry

enough

• Has the correct drying programme been selected?

• Has the cycle been interrupted (door opening, full water container)?

• Was the inserted laundry too wet (washing machine spin speed less than

1000 rpm)?

• Is the door filter dirty (filter indicator light on)?

• Is the bottom filter dirty (for more information, refer to the Instructions for

use)?

• Is the room temperature too high?

• Is the “End” and “Anticrease” indicator lamp lighting up? The drying

cycle is complete and the laundry can be taken out.

• If the drying result does not meet your expectation, select a more dry

programme or use the dryness adjustment option (if available) to optimize

the drying result.

• Is thin and thick load mixed? Are different types of materials mixed? Sort

the laundry after thickness and material and dry again.

The dryer does not

operate (after a power

failure, always press

the “Start (Pause)”

button)

• Is the plug properly inserted into the mains electricity socket?

• Is there a power failure?

• Has the fuse blown?

• Is the door properly closed?

• Has a drying programme been selected?

• Has the “Start (Pause)” button been pressed shortly after a programme

is selected? (If not, the dryer will switch off.)

• Has the start delay option been selected?

• Is the dryer overloaded?  Please remove a part of the load.

Filter, water container

indicator lamp on

• Is the lint filter clean?

• Is the water container empty?

• Has the water container been inserted correctly?

• Is the heat exchanger clean and inserted correctly?

Water droplets

underneath the dryer

• Has the heat exchanger been inserted correctly?

• Have all lint on the heat exchanger seal and the door seal been wiped

away?

• Has the water container been inserted correctly?

• If the direct drain connection is used, is it tight?

• Is the dryer leveled?

...you want to care of and clean your dryer:

Clean the filter at the

end of every cycle

• Brush lint using a soft brush or your fingertips.

• Close the filter.

• Push the filter back into place.

Empty the water

container at the end of

every drying cycle

• Pull the handle to remove the water container.

• Empty the water container.

• Replace the water container when empty by pushing it completely back

into place.

Clean the heat

exchanger at least

once a month

• Clean the heat exchanger under running water.

• Remove all fluffs from the seals.

• Clean the heat exchanger housing (for further information see chapter

“Cleaning the heat exchanger” in the Instructions for use).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht Excellence 7210 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht Excellence 7210

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info