Bedienungsanleitung Bauknecht gsf 4030 ws (Seite 10 von 10) (Englisch)

124911

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

If a fault occurs, before contacting our After-Sales Service, make the following

checks to try and remedy the problem.

Restart the wash programme to see if the

fault repeats.

•

Press the

Start

button for about 5 seconds

until the

Start

indicator lamp switches off.

•

Briefly press the

Start

button.

If the malfunction persists, switch off the

appliance and turn off the water tap. Call our

After-Sales Service.

The appliance will not switch on:

•

Power plug properly inserted in the mains

socket?

•

Power failure?

•

Have you switched the dishwasher on?

•

Have you pressed the

Start

button?

•

Have you set the delay timer (if fitted)?

•

Tap turned on? If not:

•

Turn on the water tap.

•

Make sure the water hose filter is not

clogged.

To do this, turn off the water tap, disconnect

the water hose, clean the filter, reconnect

the water hose to the tap and turn on the tap.

•

Filters clogged?

Crockery loaded upside down?

When loading large items in particular, make

sure the water circulates and does not collect

inside them.

•

Door closed properly?

•

Fault indicated?

The

Start

indicator lamp or indicator lamp

F1...F9 flashes (depending on the model

installed), if a fault is detected. F9 flashes

(depending on the model installed), if a fault

is detected.

Other fault signals depending on the model

installed:

The indicator lamp on the control panel

flashes to indicate that the water-stop

system has tripped. Switch off the dishwasher,

disconnect the mains plug, turn off the water tap

and contact our After-Sales Service.

Crockery still dirty after washing:

•

Have you selected the correct programme?

•

Have you used the correct amount of

detergent?

•

Filters clogged or incorrectly assembled?

•

Spray arms blocked or nozzles clogged?

•

Salt container cap screwed down?

•

Crockery loaded correctly? (the water jets

must spray the entire surface of all items).

Spotted crockery:

•

Water hardness duly checked and

regulated?

•

Salt container empty?

•

Insufficient detergent?

Spotted glasses and cutlery:

•

Too much rinse aid? (Adjust the rinse aid

regulator to a lower setting).

Note:

On some models when the

Start

button is

pressed, a pre-rinse cycle is performed prior to

the actual wash programme to regenerate the

water softener system.

Before contacting our After-Sales

Service:

try to remedy the problem

(see “Troubleshooting guide”).

Switch off the dishwasher and restart the

wash programme to see if the fault repeats.

If, after carrying out the above checks the

malfunction persists, call our After-Sales

Service and specify:

•

the nature of the problem;

•

the appliance type and model;

•

the service number

(the number after the

word Service on the

adhesive label) located

inside the door on the

right hand side;

•

your name, address and telephone number.

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

94000-gb.fm5 Page 21 Thursday, September 13, 2001 4:13 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht gsf 4030 ws Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht gsf 4030 ws

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info