Bedienungsanleitung Bauknecht GSIP 6130 (Seite 4 von 8) (Englisch)

592328

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

3. HOW TO USE THE APPLIANCE

HOW TO CHECK/FILL/ADJUST SALT

Only

use regeneration salt specifically intended for dishwashers.

a. How to check the salt level

Depending on the model, check the visual indicator . The window on the salt reservoir cap is clear when

salt needs to be added and coloured when the salt present is sufficient. In the case of appliances with an

electric indicator on the control panel, the salt indicator lights up at the end of the wash cycle when salt

needs to be added.

b. How to fill the salt container

- Remove the lower rack.

- Turn the salt container cap anti-clockwise to open it.

- When using the dishwasher for the first time, fill the salt container to the

rim with water.

- To make sure no grains of salt touch the stainless steel components, fill the

salt container up to the rim using a funnel (when filling for the first time, use

min. 0.8 kg and max. 1kg).

- Stir with the handle of a wooden spoon to help dissolve the salt.

- Close the cap of the salt container by turning it clockwise.

- Fit the lower rack.

Once regeneration salt is added,

immediately

start a wash programme (the “Pre-wash”

programme alone is

not

sufficient). Residual saline solution or grains of salt can lead to deep-

down corrosion, irreparably damaging the stainless steel components. The guarantee is not

applicable if faults are caused by such circumstances.

The salt level indicator lamp may remain lit at the end of several wash cycles.

If the water hardness level falls within category 1 (soft),

salt is required.

c. How to set the water hardness level

- Press and hold the programme selection button and the Cancel/Off button for at least three seconds.

- The hardness level set is shown on the display (where present) or the LEDs for programmes 1 - 3 indicate

the water hardness setting according to the table below.

- With each successive touch of the programme selection button, the setting increases and when it reaches 7

it returns to 1 again.

- Press and hold the START button or wait 30 seconds for the setting to be saved!

The factory setting for water hardness is 4 for medium-hard water (display 4 or programme 3

LED lights up).

Water hardness level 4 with combined action detergent

Even if you use tablets which include salt functionality, you must still add regeneration salt. They

are not effective enough at softening hard water.

If the appliance is equipped with the “Set detergent type” function (see Section “1. Quick

Reference Guide”) and this function has been selected, the salt indicator remains on starting

from water hardness level 5.

1. 2.

Water

hardness

Hardness in

German degrees

°dH

Hardness in

French degrees

°fH

Hardness in

English degrees

°eH

Setting/

Indication on

the display

Programme LED indicator

P1 P2 P3

Soft 0 - 5 0 - 9 0 - 6.3 1

Average 6 - 10 10 - 18 7 - 12.6 2

Average 11 - 15 19 - 27 13.3 - 18.9 3

Medium-hard 16 - 21 28 - 37 19.6 - 25.9 4

Hard 22 - 28 38 - 50 26,6 - 35 5

Very hard 29 - 35 51 - 63 35.7 - 44.1 6

Extremely hard 36 - 50 64 - 90 44.8 - 62.4 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht GSIP 6130 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht GSIP 6130

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info