Bedienungsanleitung Bauknecht koln 1400 (Seite 12 von 14) (Englisch)

304645

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

a. Fault in the water supply

The appliance has no or insufficient water supply.

For models with a fault display, the “Tap Off”

display lights up and the spin speed indication LED

flashes. If a digital display is fitted, “H

” and “F” are

also displayed alternately.

For models with no fault display, the washing

machine stops in the appropriate programme step.

Switch the appliance off and pull out the mains plug.

Check whether:

• the water tap is fully turned on, and the water

supply pressure is sufficient

• the water inlet hose is kinked

• the water connection mesh filters are blocked

(see “Care and maintenance”/”Mesh Filters in

the Water Connection”)

• the water supply hose is frozen up

• the washing machine has a safety hose and the

safety valve is open (red indicator in the safety

valve inspection window); In this case replace it

with a new safety hose

Reconnect the appliance to the electrical socket.

For models with a fault display, reselect the desired

programme and start it.

For models without a fault display continue the

programme by pressing the “On/Off” button again.

If the fault occurs again, please contact After-Sales

Service (see “After-Sales Service”).

b.Draining out fault

Waste water not pumped out.

For models with a fault display, the spin speed

indication LEDs flash. If a digital display is fitted,

“P

” and “F” are also displayed alternately.

For models with no fault display, the washing

machine stops in the appropriate programme step.

Switch the appliance off and pull out the mains plug.

Check whether:

• the drain hose is kinked

• the pump or the filter is blocked (see “Removing

the filter”)

IMPORTANT: before draining, make sure

that the water has cooled down.

• The water in the drain hose is frozen up

Reconnect the appliance to the electrical socket.

For models with fault display, select and start the

“Drain/Cancel” programme.

To rinse the laundry, we then recommend a short

programme without the addition of detergent.

For models without a fault display continue the

programme by pressing the “On/Off” button again.

If the fault occurs again, please contact After-Sales

Service (see “After-Sales Service”).

c. Electrical module fault

The appliance stops in the middle of a programme.

For models with a fault display, the spin speed

indicator LEDs flash. If a digital display is fitted,

“F4

” to “F16” are also displayed.

Switch the washing machine off. First of all select

and start the “Drain/Cancel” programme.

Then select and start the desired programme again.

For models with no fault display, the washing

machine stops in the appropriate programme step.

First switch the washing machine off and on again

to continue with the programme.

If the fault persists, please contact After-Sales

Service (see “After-Sales Service”).

d.Water Stop fault (if fitted)

The “Water Stop” fault may have been triggered by:

1.excess foaming

2.a leak in the washing machine.

In this case the pump is switched on automatically

in order to pump the water out.

For models with a fault display, the “Water Stop”

indicator lights up and the spin speed indicator

LEDs flash. If a digital display is fitted, “A

” and “F”

are also displayed alternately.

For models with no fault display, the washing

machine stops in the appropriate programme step.

Switch the appliance off, pull out the mains plug

and turn the water tap off.

Tilt the appliance forwards carefully to allow the

collected water to flow out from the bottom of the

appliance.

Then:

1.Plug in the appliance.

2.Turn the water tap on (if water immediately

flows into the appliance again, without the

appliance being started, there is a fault. Turn off

the tap and notify After-Sales Service).

3.For models with fault display, select and start the

desired programme again.

For models with no fault display, continue the

programme by pressing the “On/Off” button again.

If the fault occurs again, please contact After-Sales

Service (see “After-Sales Service”).

“Water Stop” fault when the programme

selector switch is in the “ ” position.

The pump is switched on automatically in order to

pump the water out.

For models with fault display the washing machine

will also detect a Water Stop fault (leak) if the

programme selector is in the “ ” position. In this

case the digital display (if one exists) alternately

shows “A

” and “F”.

For models with no fault display, the “Water Stop” fault

is detected when the appliance is switched on again.

Pull the mains plug out and ensure that the water

tap is turned off.

Tilt the appliance forwards carefully to allow the

collected water to flow out.

Then:

1.Plug in the appliance.

2.Turn the water tap on (if water immediately

flows into the appliance again, without the

appliance being started, there is a fault. Turn off

the tap and notify After-Sales Service).

4gb10008.fm Page 27 Thursday, January 8, 2004 3:06 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht koln 1400 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht koln 1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info