Bedienungsanleitung Bauknecht OBIC Ecosilent 7540 (Seite 7 von 8) (Englisch)

806775

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

CLEANING THE FILTER ASSEMBLY

Regularly clean the lter assembly so that the lters do not clog and

that the waste water ows away correctly.

Using dishwasher with clogged lters or foreign objects inside ltration

system or sprayarms may cause unit malfunction resulting in lose of

performance, noisy work or higher resources usage.

The lter assembly consists of three lters which remove food residues

from the washing water and then recirculate the water.

The dishwasher must not be used without lters or if the lter is

loose.

At least once per month or after each 30 cycles, check the lter assembly

and if necessary clean it thoroughly under running water, using a non-

-metallic brush and following the instructions below:

1. Turn the cylindrical lter A in an anti-clockwise direction and pull it

out (Fig 1).

2. Remove the cup lter B by exerting a slight pressure on the side

aps (Fig 2).

3. Slide out the stainless-steel plate lter C (Fig 3).

4. In case you nd foreign objects (such as broken glass, porcelain,

bones, fruit seeds etc.) please remove them carefully.

5. Inspect the trap and remove any food residues. NEVER REMOVE the

wash-cycle pump protection (black detail) (Fig 4).

After cleaning the lters, re-place the lter assembly and x it in

position correctly; this is essential for maintaining the ecient

operation of the dishwasher.

CLEANING THE WATER INLET HOSE

If the water hoses are new or have not been used for an extended

period of time, let the water run to make sure it is clear and free

of impurities before performing the necessary connections. If this

precaution is not taken, the water inlet could become blocked and da-

mage the dishwasher.

CLEANING THE SPRAY ARMS

On occasions, food residue may become encrusted onto the spray arms

and block the holes used to spray the water. It is therefore recommen-

ded that you check the arms from time to time and clean them with a

small non-metallic brush.

To remove the upper spray arm, turn the plastic locking ring in an

anti-clockwise direction. The upper spray arm should be replaced so

that the side with the greater number of holes is facing upwards.

The lower spray arm may be removed by pulling it upwards.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently

preventing scale buildup on heater, contributing also to better cleaning

eciency.

This system regenerates itself with salt, therefore it is required to

rell salt container when empty.

Frequency of regeneration depends on water hardness level setting -

regeneration takes place once per 6 Eco cycles with water hardness

level set to 3.

Regeneration process starts in nal rinse and nishes in drying phase,

before cycle ends.

• Single regeneration consumes: ~3.5L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

CARE AND MAINTENANCE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht OBIC Ecosilent 7540 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht OBIC Ecosilent 7540

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info