Bedienungsanleitung Bauknecht TRK 9666 (Seite 8 von 15) (Englisch)

572333

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

Before Using the Dryer / Connections

1. Removing the packaging

and check

•

After unpacking, make sure

that the dryer is undamaged. If

in doubt, do not use the dryer.

Contact After-Sales Service or

your local retailer.

•

Keep the packaging materials

(plastic bags, polystyrene parts,

etc.) out of reach of children, as

they are potentially dangerous.

•

Remove the protective foil

from the control panel.

2. Electrical Connections

•

Electrical connections must be

carried out by a qualified

technician in compliance with

the manufacturer's instructions

and current standard safety

regulations.

•

Electrical connection must

comply with local Electricity

Board regulations.

•

Voltage information, power

consumption and the required

fuse protection is shown on the

rating plate mounted at the

rear of the dryer.

•

The manufacturer cannot

accept any liability for personal

injury or damage to property

resulting from failure to

adhere to these instructions.

•

The dryer must be earthed as

prescribed by law.

•

Do not use extension leads or

multiple adaptors.

•

Before any maintenance on the

dryer disconnect it from the

mains supply.

•

Do not operate the dryer if it

has been damaged during

transport. Contact one of our

After-Sales Service technicians.

•

Mains cables must be replaced

by an original cable and is only

to be carried out by a

technician from After-Sales

Service or an authorized

electrician.

•

After installation access to the

mains plug has to be

guaranteed, or the all-pole

disconnection has to be

possible with a switch.

3. Installation

•

Do not install your dryer where

it can be subject to extreme

conditions, such as: poor

ventilation, temperatures

around freezing or above

35° C.

•

Before running the first cycle

ensure the water container and

heat exchanger are correctly

positioned.

•

Only for water container top

version: if possible use the hose

supplied to drain the water

directly into the domestic

plumbing system. This will

avoid having to empty the

water container at the end of

each drying cycle since the

condensation water can be

directly drained away.

•

Take care not to install the

dryer on a deep-pile carpet.

•

Take care not to trap the mains

cable between the dryer and

the wall.

Stability:

When installing the dryer

always carefully level the dryer

adjusting the four feet and

check the correct levelling with

a spirit level.

To built in the dryer

Remove the work-top and

replace it with the Built-In kit

UBS 10 (according to Eec

Electrical Regulations), which

can be ordered at your dealer.

Stacking kit

Your dryer can be stacked on

top of your front loading

washing machine. To do this,

use stacking kit AMH 752,

available at your dealer.

Minimum housing

dimensions:

Width: 600 mm

Height: 850 mm

Depth: 600 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht TRK 9666 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht TRK 9666

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info