Bedienungsanleitung Bauknecht WA 43510 (Seite 5 von 23) (Englisch)

572341

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Before using the washing machine

1.Remove the packaging and

check

•

After unpacking, make sure

that the washing machine is

undamaged. If in doubt, do

not use the washing machine.

Contact After-Sales Service or

your local retailer.

•

Check that the accessories and

supplied parts are all present.

•

Keep the packaging materials

(plastic bags, polystyrene

parts, etc.) out of the reach of

children; they can constitute a

possible source of danger.

2.Remove the transit bolts

•

The washing machine is fitted

with a transport bolts to avoid

any possible damage to the

interior during transport.

Before using the washing

machine, the transport bolts

must be removed (see

“Installation/Remove the

transit bolts”).

3.Install the washing

machine

•

Remove the protective foil

from the control panel.

•

Move the appliance without

lifting it by the worktop.

•

Install the appliance on a solid

and level floor surface,

preferably in a corner of the

room.

•

Make sure that all feet are

resting correctly on the floor

and that the washing machine

is perfectly level and stable

(use a spirit level - see

Installation/Adjusting the

Feet).

4.Water inlet

•

Connect the water supply inlet

hose in accordance with the

regulations of your local water

company (see “Installation/

Connect the water inlet

hose”).

5.Drain hose

•

Connect the drain hose to the

siphon or hook it over the edge

of a sink by means of the “U”

bend (see “Installation/

Connect the water drain

hose”).

•

If the washing machine is

connected to a built-in

pumping out system, ensure

that the latter is equipped with

a vent to avoid simultaneous

loading and draining of water

(siphoning effect).

6.Electrical connections

•

Electrical connections must be

carried out by a qualified

technician in compliance with

the manufacturer's

instructions and local safety

regulations.

•

Data concerning voltage,

consumption and fuses are

located on the inside of the

appliance door.

•

The appliance must be

connected to the mains

exclusively by means of a socket

with an earth connection in

accordance with established

regulations. The washing

machine must be earthed by

law. The manufacturer declines

all responsibility for injury to

persons or pets, or damage to

property caused by non-

compliance with the above-

mentioned regulations.

•

Do not use extension leads or

multi sockets.

•

Before any maintenance on

the washing machine

disconnect it from the mains

supply.

•

Access to the mains plug or to

disconnection from mains

supply via a double-pole switch

must be ensured at all times

following the installation.

•

Do not operate the washing

machine if it has been

damaged during transport.

Inform the After-Sales Service.

•

Mains cable replacement is

only to be carried out by After-

Sales Service.

•

The washing machine must

only be used in the household

for the prescribed uses.

Minimum housing

dimensions:

Width: 600 mm

Height: 825 mm

Depth: 600 mm

•

Water inlet: Cold water only

•

Tap: 3/4 threaded

hose

connection

•

Water

pressure

(flow

pressure):

100-1000 kPa

(1-10 bar).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht WA 43510 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht WA 43510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info