Bedienungsanleitung Bauknecht WA 89890 (Seite 25 von 40) (Englisch)

572349

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Worktop for built-

under models

The appliance

must only

installed beneath a continuous

worktop.

The appliance

may only

built under using the

intermediate cover panel of

the UBS base set. This can be

obtained from specialist

dealers or After Sales Service.

Pull out the mains plug.

Remove the worktop fixing

screws on the rear of the

appliance.

Slide the worktop fully

backwards, lift it up and

remove it.

Install the base set

following the relevant

instructions.

Refit the fixing screws and

tighten them.

Connect the appliance to

the electricity.

Connect the water

inlet hose

For models with straight

hose:

Insert the mesh filter

(already premounted on

the hose end or included in

the accessories) into the

threaded tap coupling.

Carefully screw the water

inlet hose connection onto

the tap by hand.

Make sure there are no

kinks in the outlet hose.

Turn the tap on fully and

check that the joints at the

washing machine and the

tap are watertight.

If the hose is too short,

replace it with a suitable

length of pressure resistant

hose (1000 kPa min, EN 50084

approved type).

Check the inlet hose regularly

for brittleness and cracks and

replace if necessary.

The washing machine can be

connected without a non-

return valve.

For models with Water

Stop hose:

Screw the threaded

connection with the mesh

filter onto the tap.

Turn the tap on fully and

check that the tap joint is

watertight.

If the flexible hose is too short,

replace it with a 3 m Water

Stop hose (available from After

Sales Service or from your

dealer). This replacement is

only to carried out by a trained

electrician.

The appliance

must not

connected to the mixing tap of

an un-pressurized water heater.

Depending on the design, the

inlet hose and the plastic

enclosure at the tap

connection contain electrical

components.

Do not cut the hose and do

not immerse the plastic

enclosure in water.

Isolate the appliance from the

mains immediately if the hose

is damaged.

Connect the water

drain hose

Connect the drain hose to

the siphon or hook it over

the edge of a sink by means

of the U bend supplied.

Make sure there are no

kinks in the drain hose.

Secure the hose so that it

cannot fall down while the

appliance is running.

Small hand basins are not

suitable.

To make an extension, use a

hose of the same type. Secure

the connections with clips.

Max. Overall drain hose

length: 2.50 m

Maximum drain height:

1.25 m

Depending on the

model, the drain hose

can be:

installed in the upper part of

the washing machine. In this

case the hose can be undone

from both fastenings.

Installed in the lower part

of the washing machine.

Important:

In this case never undo the

hose from the right-hand

fastening, otherwise the

appliance could overflow

when operating.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht WA 89890 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht WA 89890

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info