5019 401 05427
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1. Turn the
programme selector
to the desired
programme. The display shows the programme
duration in hours and minutes as well as the
predefined temperature. The
“Start/Pause”
button
flashes.
2. The
temperature
can be altered by pressi
“Temperature” button.
3. The indication lamp of the predefined
spin speed
lights up; in case you want to set another spin
press the “Variable spin” button.
Push the button(s) o
indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Umbinations of options are
deselected automati
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycl
approximately 15 min.
• Do not use liquid
activating the Prewash option.
“Rinse hold” button
• The laundry remains in the last rin
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load”
“Delicates”.
• It is particularly useful if yo
to a later time,
• If you select “Rinse hold”, do
soak fo
Note:
The programme stops to “Rinse hold” at the
time the “Rinse hold” li
indicator is on. The indication
“Start
Pau
button flashes.
Tse hold” option:
• Press the
“Start/P
button; the programme will
terminate automatically with
present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector to the “Drain
press the
“Start/P
button.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very
soft water
allergies.
“Easy ironing” button
• Can be used together with “Cotton”, “Synthetics” and
“Daily load” programmes to make ironing easier
• Increases the water
very gently
“
• Every programme has a predefined spin speed.
• Press the button to se
• If spin speed “0” is sel
cancelled but intermediate spin peaks remain during
rinse. T
CONSUMPTION DATA
Progra
T
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. P
(hours : minutes)
*
White Cotton / Antibacterial 95 6.0 59
**
1.90 2:00
Cotton 60 6.0 56 1.14 2:10
Cotton with “Eco”
***
60 6.0 49 1.02 2:20
Cotton 40 5.0 56 0.70 2:00
SuperEco 60 6.0 51 0.72 4:00
Synthetics 60 2.5 50
**
0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
Delicates 30 1.5 60 0.50 0:45
W 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Lingerie 30 1.0 45 0.40 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relae o
*
The time indicated on the display can the table, because it takes into account the houson
applicable at that time.
**
Tut.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Eco” button
• With a modified temperature
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
If there is a programme setting which you use frequently,
the appliance offers thlity to save one setting for
each programme so that it can be use
pushing one button.
• Select the desired programme, temperature, spin
speed and option(s), pu
“Favourites”
button for at le
“Favourites”
shortly flashes and then lights up - the
programme setting is saved.
Next time you want to
setting, select the programme, push the
“Favourites”
button and start by pushing
“Start/Pa
.
If you want to replace the saved programme setting
by another one:
• Push the programme butto
speed and options as desired and then press and hold
the
“Favourites”
button for at least 3 seconds. The
previously saved programme setting will be re
by the new one.
The “Start Delay
consumer’s convenience, for example at nigh
electricity is cheaper. Do not use liquid detergent when
activating the “
• Select programme, temperature and options.
• Press the “Start Delay
by 1 to 23 ho
• Press the
“Start/Pa
button.
The indication
lights up and the countdown of th
During the countdown, the light over
Delay
on the display flashes.
• The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
• Once having pressed the
“Start/P
button, the
number of hours preselected can be reduced by
pressing and holding the “Start Delay
hour on, the delay time can also be reduced in steps
10 minutes.
T
..before you press the “Start/P
• T
press the
“Reset”
button.
..after having pressed the “Start/Pause” button:
• Press the
“Reset”
button for at least 3 seconds - the
start delay time disappears from the
Open the tap and press the
“Start/Pause”
button. The
indication lamp over the
“Start/P
button lights
The programme sequence indicator shows the current
programme phase, running from left to
Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the
remaining time is newly calculated in ce
phases. If this is the case,
an animation appears on
display
.
Before starting and after end of a programme,
lights to show t
wash programme is running, the door
must on no accoun
urgent need to open it during a running programme, refer
to “Cancel (Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a
fault in an el
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
“Troubleshooting Guide” in your Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether
hose is kinked or the fil
case refer to the Instructions for Use (“Removing the
Filter”).
• All the lights of the programme sequence i
are off
1. Turn the programme selector to the
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start/P
button to pau
programme. The light flashes.
2. Select the new programme, temperature, any options
and another spin speed if you want.
3. Press the
“Start/P
button agai
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
The
“Reset”
button cancels a programme before the end.
• Press the
“Reset”
button for at least 3 seconds. Any
existing water is drained out before th
opened.
SA
START DELAY
PROG
“DOOR OPEN” INDICATION
RED INDICA
PROGRAMME END
CHANGE PROG
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
40105427GB.f
Black process 45.0° 100.
