Load your laundry, close the door properly and add detergent as
indicated on the front page and as described in the chapter “Detergent
and Additives” in your Instructions for Use (remove separator in
detergent dispenser for use of powder detergent if necessary).
1.Turn the
programme selector
to the desired programme. The
display shows the programme duration in hours and minutes as well as
the predefined temperature. The
“Start (Pause)”
button blinks.
2.The
temperature
can be altered by pressing the
“Temperature” button.
3.The indication lamp of the predefined
spin speed
lights up; in case
you want to set another spin speed, press the “Variable spin” button.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and option is not possible,
the lights switch off automatically. Unsuitable combinations of
options are deselected automatically.
“Clean +” button
•Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
•Choose temperature of 30 or 40°C and use with maximum load.
•Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
•Prolongs the programme by approx. 10 to 15 minutes.
•Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborate bleaches must not be used!
“Prewash” button
•Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
•Do not use liquid detergent for the main wash when activating
the Prewash option.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft
water, washing baby linen and helping people with allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and a very
gentle spin.
“Rinse hold” button
•Press the button if you want to postpone spinning to a later
time or if you want to drain only.
•The laundry will remain in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent
colours from changing.
•Do not leave the laundry to soak in the “Rinse hold” for too long.
•The washing machine stops to rinse hold as soon as the “Rinse
hold” light in the programme sequence indicator blinks; the
“Start (Pause)”
button also blinks.
To terminate the “Rinse hold”:
•If you want to drain only without spinning: Press the
“Start
(Pause)”
button to start the drain process.
•If you want to spin your laundry: Press the “Variable spin”
button to select the desired spin speed and then
“Start
(Pause)”
to start the spin cycle.
“Variable spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If you select spin speed “0”, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton / Hygienic +958.082
**
2.402:20
Coloured Cotton
608.0591.362:20
Coloured Cotton408.0770.752:05
Synthetics603.546
**
0.851:35
Synthetics403.5420.501:20
Delicates302.5600.400:45
Wool402.0600.600:45
Handwash402.0450.600:40
Lingerie302.0450.350:36
Eco Cotton
***
608.0591.044:00
Sport303.5540.551:34
Super Eco608.0750.954:00
Daily load406.0730.601:00
Speed 15303.0300.200:15
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60456. Consumption data in the home may vary
with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label (with separator in dispenser removed for powder detergent use).
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
•Select programme, temperature and options.
•Press the “Start delay” button to select a delay time up to 23
hours; the light of the
“Start (Pause)”
button blinks.
•Press the
“Start (Pause)”
button; the countdown of the delay
time begins. The light of the
“Start (Pause)”
button stops
blinking and is on; the light of the start delay button will keep
blinking until the programme starts.
•As soon as the programme starts, the start delay on the display
is replaced by the remaining programme time, and the light of
the “Start delay” button goes off.
•Once having pressed the
“Start (Pause)”
button, the number
of hours preselected can be changed by pressing and holding
the “Start delay” button.
To cancel the “Start delay”
..before you press “Start (Pause)”:
•Turn the programme selector to another position or press the
“Reset/Drain”
button.
..after having pressed “Start (Pause)”:
•Press
“Start (Pause)”
- the delay time disappears from the
display; press
“Start (Pause)”
again to start the selected
programme immediately.
Open the tap and press
“Start (Pause)”
; the light stops blinking and is on.
The programme sequence indicator shows the current programme
phase, running from left to right through Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is the
case,
an animation appears on the display
.
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
•Turn the programme selector to a programme position, or run
a programme as usual.
•Press the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds; a key-like symbol will shortly
appear on the display to indicate that the child lock is active.
Any time you try to change a programme setting with active child
lock, the display will shortly show the key-like symbol. The
programme setting cannot be changed anymore; the only change
possible is to switch the washer off by turning the programme
selector to the “Off/O” position. To deactivate the child lock:
•Press again the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds.
Before starting and after end of a programme, the lamp lights to show
that the door can be opened. As long as a wash programme is running,
the door remains locked and must on no account be forced open. In
case you have an urgent need to open it during a running programme,
refer to “Reset a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a fault in an
electrical component. Refer to the “Troubleshooting Guide” in your
Instructions for Use; if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water
tap; if the indication still lights up, refer to the “Troubleshooting
Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is
kinked or the filter must be cleaned; in the latter case refer to the
Instructions for Use (“Removing the Filter”).
•The display shows “End” and the “Door open” indication lights.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
•Leave the door ajar to allow the drum to dry.
In case you used too much detergent, a small vertical bar will light
next to the overdosage symbol on the right of the display when
the wash programme is finished; use less detergent next time. Too
much foam by detergent overdosing can also lead to interruption
of a wash cycle; in this case the display shows “Fod” - follow the
recommendations in the “Troubleshooting Guide” in your
Instructions for Use to solve the problem.
1.Press
“Start (Pause)”
to pause the programme; the light
blinks.
2.Select the new programme, temperature, any options and
another spin speed if you want.
3.Press
“Start (Pause)”
again. The light is on, and the programme
continues at the same position where the previous programme was
interrupted. Do not add detergent for this programme.
The
“Reset/Drain”
button cancels a programme before the end.
•Press the
“Reset/Drain”
button for at least 3 seconds; “rES”
appears on the display. Any existing water is drained before
the door can be opened.
START DELAY
PROGRAMME START
CHILD LOCK
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
DETERGENT OVERDOSAGE INDICATION
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
The sensor Technology automatically adapts Programme Time, Water and Energy consumption to the size of your wash load.
40105517GB.fm Page 2 Thursday, November 26, 2009 4:57 PM
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Bauknecht WAE 8749 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
