5019 401 05518
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use
(remove separator in detergent dispenser for use of powder
detergent if necessary).
Turn the programme selector to the desired programme; the light
of the
“Start (P
button blinks. The
temperature
and
spin
speed
indicated on the display can be altered by pressing
“Temperature” button or the “Variable spin” button.
When the combination of programme and additional option(s) is
not possible, the indication lights switch o
Unsuitable combinations of options are deselected automatically.
“Clean+” button
• Choose this option if you use an in-wash additive for stain removal
(powder
efficiency to get better wash performance and stain removal.
• Choose temperature of 30 or 40°C and use with maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
• P
• Appropriate for
basis.
Chlorine or perborat
“Prewash” button
• Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
• Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Rinse hold” button
• The laundry remains in the last rins
progressing to the fnal spin cycle, to avoid creasing and
prevent colours from changing.
• The programme stops to “Rinse hold” when the “Rinse hold”
symbol on
“Start
(P
button blinks as well.
• T
any spinning, press the
“Start (P
button.
• T
the "Vct the desired s
then
“Start (P
to start the spin cy
• Do not leave the laundry to soak for too long in the “R
“Intensive rinse” button
• More wat
• This option is pa
for washing baby linen, and helps people with allergies.
“
• Every programme has a predefined spin speed.
• P
• If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one butto
• Select the desired programme, temperature, spin speed and
option(s), push and ho
“Favourites”
button for at least 3
seconds. The lamp of the
“Favourites”
button shortly blinks and
then lights up - the programme s
CONSUMPTION DATA
Programme
Te m p r a t u r e
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton / Hygiene + 95 8.0 82
**
2.40 2:20
Coloured Cotton 60 8.0 59 1.36 2:20
Coloured Cotton 40 8.0 77 0.75 2:05
Synthetics 60 3.5 46
**
0.85 1:35
Synthetics 40 3.5 42 0.50 1:20
Delicates 30 2.5 60 0.40 0:45
W 40 2.0 60 0.60 0:45
Handwash 40 2.0 45 0.60 0:40
Lingerie 30 2.0 45 0.35 0:36
Eco Cotton
***
60 8.0 59 1.04 4:00
Sport 30 3 54 0.55 1:34
Super Eco 60 8 75 0.95 4:00
Daily load 40 6.0 73 0.60 1:00
Speed 15 30 3.0 30 0.20 0:15
Consumption values were measured in normalized conditions in compliance with Stane
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type o
*
The time indicated on the display can deviate froons
applicable at that time.
**
Tut.
***
Reference P
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO
SA
Next time you want to use your individual programme setting,
select the programme, shortly push the
“Favourites”
button and
start by pushing
“Start (P
.
If you want to replace the saved programme setting by another
one, proceed as already described above.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
• Select programme, temperature, spin speed and options.
• P
steps between 0:30 and 23:00 hours.
• P
“Start (P
button; the light stops blinking and
becomes solid.
The countdown of the delay time begi
the delay time and the colon between hours and minutes
• The time
starts and it is replaced by the remaining programme time.
T
..before you press the “Start (P
• P
“Reset/Dra
button, or set the s
“0:00” - the delay t
..after having pressed the “Start (Pause)” button:
Press the
“Start (Pause)”
button - the delay time disappears
from the display; press
“Start (Pause)”
again to start the selected
programme immediately
Before starting and after end of a programme, the symbol lights to
show that the door can be opened. As long as a wash programme is
running, the door remains locked and must on no account be forced
open. In case you have to open it urgently durin
programme, refer to “Reset a running programme before the end”.
Open the tap and press the
“Start (Pause)”
button; the blinking
“Start (Pause)”
button light becomes constant. The programme
sequence indicator shows
from left to right through wash, rinse, spin, drain. In some phases, t
remaining programme time is newly calculated - if this is the case, the
“green intelligence sensor” on the display will fade,
and the remaining t
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in th
• Turn the programme select a programme position, or run
a programme as usual.
• Press the “Temperature” and the “Variable spin” button
simultaneously for at least 3 seconds. T
will shortly blink and then light up to indicate that the
child lock is active.
The programme setting cannot be changed anymore; the only change
possible is to switch the washer off b
to the “Off/O” position. To deactivate the child lock, proceed in the
same way as for activating it.
If one of the red failure indications on the display lights up, refer to
the “Troubleshooting Guide” in your “Instructions for Use”.
• The display shows “End”, and the “Door open
lights up.
1. T
2. Close the water tap.
3. Open the door and unload the machine.
• Leave the door ajar to allow the drum to dry.
• If you do not turn the programme selector to the “
position, all lights of the contro
to save energy - only “End” will remain on the dis
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time. If the symbol
lights up and the display shows “Fod”, too much foam interrupted
the wash process; refer to the “Trouble
Instructions for Use.
1. Pres
“Start (Pause)”
button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3 Pres
“Start (Pause)”
button again. The new programme
continues at the same po
interrupted. Do not add deterge
The
“Res
button cancels a programme before the end.
• Press the
“Reset
button for at least 3 seconds;
an
out before the door can be opened.
START DELAY
“DOOR OPEN” INDICATION
PRO
CHILD LOCK
RED FAIL
PROGRAMME END
DETERGENT OV
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
The Sensor Technology automatically adapts Programme Time, Water and Energy consumption to the size of your wash load.
40105518GB.fm Page 2 Friday, November 2
Black process 45.0° 150.0 LPI
