Bedienungsanleitung Bauknecht WAK 7771 BK (Seite 2 von 2) (Englisch)

577822

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 401 05534

Add detergent as indicated on the front page and as described in

the chapter “Detergent and Additives” in your Instructions for Use.

1. Turn the

programme selector

to the desired programme.

The display shows the programme duration in hours and

minutes as well as the predefined temperature. The lamp of

the

“Start”

button blinks.

2. The

temperature

can be altered by pressing the

“Temperature” button.

3. The indication lamp of the predefined

spin speed

lights up; in

case you want to set another spin speed, press the “Spin” button.

Push the button(s) of any option(s) desired - the respective

indication lights up.

When the combination of programme and additional option(s) is

not possible, the indication lights switch off automatically.

Unsuitable combinations of options are deselected automatically.

“Clean+” button

• Choose this option if you use an in-wash additive for stain removal

(powder, for example “Vanish”) - it will optimize the additive’s

efficiency to get better wash performance and stain removal.

• Choose temperature of 30 or 40°C and use with maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together with

your detergent (only use powder detergent with this option).

Respect the manufacturer’s dosing instructions.

• Prolongs the programme by approx. 10 to 15 minutes.

• Appropriate for use of stain removers and bleaches on oxygen

basis.

Chlorine or perborate bleaches must not be used!

“Prewash” button

• Only for heavily soiled loads (for example sand, granular dirt).

Increases the cycle time by approximately 15 min.

• Do not use liquid detergent for the main wash when activating

the Prewash option.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing and prevent

colours from changing.

• It is particularly useful if you want to postpone spinning to a

later time, or if you want to drain only.

• If you select “Rinse hold”, do not leave the laundry to soak for

too long.

Note:

The programme stops to “Rinse hold” at the time the

“Rinse hold” light in the programme sequence indicator is on.

The indication lamp next to the

“Start”

button blinks.

Terminate the “Rinse hold” option:

•Press the

“Start”

button; the programme will terminate automatically

with the final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the programme selector

to the “Drain” programme and press the

“Start”

button.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very soft

water, washing baby linen and helps people with allergies.

“Easy ironing” button

• Reduces creasing by an increased water quantity and a very

gentle spin.

“Spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is cancelled but

intermediate spin peaks remain during rinse. The water is

drained out only.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

White Cotton 95 7.0 74

2.10 2:10

Cotton 60 7.0 54 1.19 2:20

Cotton 40 7.0 69 0.75 2:05

SuperEco 60 7.0 69 0.84 4:00

Synthetics 60 3.0 46

0.80 1:35

Synthetics 40 3.0 42 0.40 1:20

Daily load 40 4.0 48 0.50 1:00

Quick wash 30 4.0 48 0.25 0:30

Delicates 30 1.5 60 0.50 0:45

Wool 40 1.0 60 0.55 0:45

Handwash/Lingerie 40 1.0 45 0.55 0:40

Handwash/Lingerie 30 1.0 45 0.45 0:36

Eco Cotton

***

60 7.0 54 0.91 4:00

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with

respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display can deviate from the values in the table, because it takes into account the operating conditions applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

If there is a programme setting which you use frequently, the

appliance offers the possibility to save one setting for each

programme so that it can be used again by just pushing one button.

• Select the desired programme, temperature, spin speed and

option(s), push and hold the

“Favourites”

button for at least

3 seconds. The lamp next to

“Favourites”

shortly blinks and

then lights up - the programme setting is saved.

Next time you want to use your individual programme setting,

select the programme,

shortly

push the

“Favourites”

button and

start by pushing

“Start”

If you want to replace the saved programme setting by

another one:

• Push the programme button, select temperature, spin speed

and options as desired and then press and hold the

“Favourites”

button for at least 3 seconds. The previously

saved programme setting will be replaced by the new one.

The “Start delay” allows to run the machine at the consumer’s

convenience, for example at night when electricity is cheaper. Do

not use liquid detergent when activating the “Start delay”.

• Select programme, temperature and options.

• Press the “Start delay” button to select the delay time by 1 to

23 hours.

•Press the

“Start”

button.

The indication light of the “Start delay” button starts to blink

and the countdown of the delay time begins.

During the countdown of the delay time, the light of the “Start

delay” button and the dot on the display keep blinking.

• The time delay indication disappears when the programme

starts and it is replaced by the remaining programme time.

• Once having pressed the

“Start”

button, the number of hours

preselected can be reduced by pressing and holding the “Start

delay” button. From 1 hour on, the delay time can also be

reduced by minutes.

To cancel the “Start delay”

...before you press the “Start” button:

• Turn the programme selector to another position or press the

“Reset”

button.

...after having pressed the “Start” button:

•Press the

“Reset”

button for at least 3 seconds - the start

delay time disappears from the display.

Open the tap and press the

“Start”

button. The indication lamp of

the

“Start”

button lights up. The programme sequence indicator

shows the current programme phase, running from left to right

through Wash, Rinse, Spin/Drain.

The display shows the remaining programme time. Due to

variations in load and temperature of inlet water, the remaining

time is newly calculated in certain programme phases. If this is the

case,

an animation appears on the display

Before starting and after end of a programme, the lamp lights to show

that the door can be opened. As long as a wash programme is running,

the door remains locked and must on no account be forced open. In

case you have an urgent need to open it during a running programme,

refer to “Reset a running programme before the end”.

“Service”

Lighting up of the “Service” indication can be caused by a fault in an

electrical component. Refer to the “Troubleshooting Guide” in

your Instructions for Use; if the fault persists, contact our After

Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open the water

tap; if the indication still lights up, refer to the “Troubleshooting

Guide” in your Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain hose is

kinked or the filter must be cleaned; in the latter case refer to the

Instructions for Use (“Removing the Filter”).

• All the lights of the programme sequence indicator are off,

and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press the

“Start”

button to pause the programme. The light blinks.

2. Select the new programme, temperature, any options and

another spin speed if you want.

3. Press the

“Start”

button again. The new programme continues at

the same position where the previous programme was

interrupted. Do not add detergent for this programme.

The

“Reset”

button cancels a programme before the end.

•Press the

“Reset”

button for at least 3 seconds; “rES”

appears on the display. The water is drained out; it may last

some time until the door can be opened.

SAVE YOUR FAVOURITE PROGRAMMES

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

40105534GB.fm Page 2 Thursday, April 22, 2010 6:34 PM

Black process 45.0° 150.0 LPI

Bauknecht WAK 7771 BK Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht WAK 7771 BK

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info