Bedienungsanleitung Bauknecht was 4349 (Seite 15 von 20) (Englisch)

306036

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Fault indicators

Fault in the water supply

The appliance has no or

insufficient water supply.

For models with a fault display, the

display

“Tap Off”

lights up, an

acoustic signal sounds and the spin

speed indicator lights flash. If a

digital display is fitted, “H

” and “F”

are also displayed alternately.

For models with no fault display,

the washing machine stops in the

appropriate programme step.

Switch the appliance off and pull

out the mains plug.

Check whether:

•

The water tap is fully turned

on, and the water supply

pressure is sufficient.

•

The water inlet hose is kinked.

•

The water connection mesh

filters are blocked (see Care

and Maintenance/Water hose

mesh filter).

•

The water supply hose is

frozen up.

•

The washing machine has a

safety hose and the safety

valve is open (red indicator in

the safety valve inspection

window); In this case replace it

with a new safety hose.

Reconnect the appliance to the

electrical socket.

For models with a fault display,

reselect the desired programme

and start it.

For models without a fault

display continue the programme

by pressing the “On/Off” button

again.

If the fault occurs again, please

contact After Sales Service (see

“After Sales Service”).

Draining fault

Waste water not pumped out.

For models with a fault display, an

acoustic signal sounds and the spin

speed indicator lights flash. If a

digital display is fitted, “P

” and “F”

are also displayed alternately.

For models with no fault display,

the washing machine stops in the

appropriate programme step.

Switch the appliance off and pull

out the mains plug.

Check whether:

•

The drain hose is kinked (see

“Installation/Connect the

water drain hose”);

•

The pump or the filter is

blocked (see “Removing the

Filter”);

IMPORTANT:

Before

draining, make sure that the

water has cooled down.

•

The water in the drain hose is

frozen up.

Reconnect the appliance to the

electrical socket.

For models with fault display,

select and start the “Drain/

Cancel” programme.

To rinse the laundry, we then

recommend a short programme

without the addition of

detergent.

For models without fault display,

continue the programme by

pressing the “On/Off” button

again.

If the fault occurs again, please

contact After Sales Service (see

“After Sales Service”).

Fault in an electrical

component

The appliance stops in the middle

of a programme.

For models with a fault display,

an acoustic signal sounds and the

spin speed indicator lights flash.

If a digital display is fitted, “F4

”

to “F16

” are also displayed.

Switch the washing machine off.

First of all select and start the

“Drain/Cancel” programme.

Then select and start the desired

programme again.

Luminous

display

acoustic

signal

Spin

speed

lights

Digital display

(if fitted)

Fault description

“Water tap” 30 sec flash “H” and “F” “Fault in water supply”

- 30 sec flash “P” and “F” “Fault when draining”

- 30 sec flash from “F4” to “F16” “Fault in an electrical component”

“Water Stop” 30 sec flash “A” and “F” “Water Stop fault”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bauknecht was 4349 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht was 4349

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info