Bedienungsanleitung Bauknecht WAT 4587 (Seite 2 von 19) (Englisch)

584995

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

GB 2

DEFINITION OF USE

This washing machine is exclusively destined to wash

machine washable laundry in quantities which are usual

for private households.

•

Observe the instructions given in these Instructions

for Use and the Programme Chart when using the

washing machine.

•

Keep these Instructions for Use and the Programme

Chart; if you pass on the washing machine to

another person, also give him/her Instructions for

Use and Programme Chart.

BEFORE USING THE WASHING MACHINE

1. Remove the packaging and check

Cut and remove the shrink-wrap.

Remove the top protection and the protective

corners.

c. Remove the bottom protection by tilting and

turning the washing machine on one rear

bottom corner. Make sure that the black

plastic part of the bottom protection (if

available on the model) remains in the packing

and not in the machine bottom.

This is important, as otherwise the plastic part could

damage the washing machine during operation.

Open the lid by pressing it slightly down while

raising the handle. Remove the polystyrene cushion

(depending on model).

Remove the blue protective film from the panel

(depending on model).

•

After unpacking, make sure that the washing machine is

undamaged. If in doubt, do not use the washing machine.

Contact After-Sales Service or your local retailer.

•

Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children;

they are potentially dangerous.

•

If the appliance was exposed to the cold prior to

delivery, keep it at room temperature for a few

hours before operating.

2. Remove the transport bracket

•

The washing machine is fitted with transport screws

and a transport bracket to prevent damage during

transport.

Before using the washing machine

you must remove the transport bracket

(see

“Installation”/“Removal of transport bracket”).

3. Install the washing machine

•

Place the washing machine on a flat and stable floor

surface.

• Adjust the feet to ensure that the machine is stable

and level (see “Installation”/“Adjust the feet”)

•

In case of wooden or so-called “floating floors” (for

instance certain parquet or laminate floors), place

the appliance on a 40 x 60 cm sheet of plywood at

least 3 cm in thickness which is secured to the floor.

•

Make sure that the ventilation openings in the base

of your washing machine (if available on your model)

are not obstructed by a carpet or other material.

4. Water supply

•

Connect the water supply inlet hose in accordance

with the regulations of your local water company

(see “Installation”/“Connect the water inlet hose”).

•

Water supply: Cold water only

•

Tap: 3/4” threaded hose connection

•

Pressure: 100-1000 kPa (1-10 bar).

•

Only use new hoses for connecting the washing

machine to the water supply. Used hoses must not

be used anymore and should be discarded.

5. Drain hose

•

Connect the drain hose to the siphon or hook it

over the edge of a sink with the “U” bend (see

“Installation”/“Connect the water drain hose”).

•

If the washing machine is connected to a built-in

drainage system, ensure the latter is equipped with

a vent to avoid simultaneous loading and draining of

water (siphoning effect).

6. Electrical connection

•

Electrical connections must be carried out by a

qualified technician in compliance with the

manufacturer’s instructions and the current

standard safety regulations.

•

The technical data (voltage, power and fuses) are given

on the rating plate on the rear of the washing machine.

•

The washing machine must be connected exclusively by

means of a socket with an earth connection in

accordance with current regulations. The washing

machine must be earthed by law. The manufacturer

declines all liability for injury to persons or animals or

damage to property deriving directly or indirectly from

failure to observe the directions.

•

Do not use extension leads or multi sockets.

•

Before any maintenance on the washing machine

disconnect it from the mains supply.

•

Access to the mains plug or to disconnection from the

mains supply via a double-pole switch must be ensured

at all times following the installation.

•

Do not operate the washing machine if it has been

damaged during transport. Inform the After-Sales Service.

•

Mains cable replacement is only to be carried out by

After-Sales Service.

•

The washing machine must be connected to an effective

earthing installation, in compliance with the regulations

in force. In particular, washing machines installed in

premises containing a shower or a bath must be

protected by a differential residual current device of at

least 30 mA. Earthing the washing machine is obligatory

under the law. The manufacturer declines all liability for

injury to persons or animals or damage to property

deriving either directly or indirectly from failure to

observe the directions in these Instructions for Use.

•

The washing machine may only be used in the

household for the prescribed uses.

Dimensions:

Width: 400 mm

Height: 900 mm

Depth: 600 mm

IFU-TL HR GB.fm Page 2 Friday, November 7, 2008 2:30 PM

Black process 45.0° 100.0 LPI

Bauknecht WAT 4587 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bauknecht WAT 4587

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info