Bedienungsanleitung Baumatic bt06 6me (Seite 15 von 24) (Englisch)

128193

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Mounting

Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a

qualified technician must verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood. Do not tile,

grout or silicone this appliance to the wall. Surface mounting only.

Before beginning installation:

• Remove the fats filter/s or the suction grill/s (depending on the model in possession –see also

the relative paragraph). This/these is/are to be mounted once installation is completed.

• Remove the active carbon (*) filter/s if supplied (see also relative paragraph). This/these

is/are to be mounted only if you want to use the hood in the filtering version.

• Check (for transport reasons) that there is no other supplied material inside the hood (e.g.

packets with screws (*), guarantees (*), etc.), eventually removing them and keeping them.

• In addition check whether near the installation area of the hood (in the area accessible also

with the hood mounted) an electric socket is available and it is possible to connect a fumes

discharge device to the outside (only suction version).

• Choose the discharge outlet to use:

Only filtering version: use ONLY the upper B1 outlet (Fig. 2 - Fig. 2.2). Check that this,

once installation is completed, is not obstructed and that there is sufficient space so that the

purified fumes and steam can return easily into the kitchen.

(Fig. 3.1) Take away the pre-fractured part (B1 o B2) that closes the discharge outlet and

remove it.

Install the connection ring on the open discharge outlet (Fig. 3.2 bayonet embedded) or the

deflector (*). (Fig. 3.3).

Note: the elements marked with the symbol (*) are optional acessories

supplied only some models or elements to purchase and not supplied.

Check that the lateral wall units between which to install the hood are sufficiently robust for

installing the hood.

Otherwise mount the hooking brackets on the wall (*) to use as additional supports:

a. Insert each bracket from the rear inside the hood through the opposite slots (Fig. 4.1—Fig.

4.2).

b. Fix the brackets with the screws and threaded bushes (Fig. 4.3).

Screw the headless screws halfway. They will serve to adjust the position of the hood at the

moment of installation.

Note: the position of the brackets can be adjusted during installation, suitably loosening and

retightening the screws that fix them to the hood. (Fig. 7 - S1-S2).

Installing the aesthetic panel (*)

a. Extract the steam collector (freeing it from the blocking hooks - Fig. 5).

b. Put perforation diagram N3 on the REAR of aesthetic panel J (the arrow on the diagram

turned upward towards the UPPER EDGE of the aesthetic panel). Fig. 6

c. Make BLIND HOLES K as indicated. Fig. 6

d. Put the steam collector over the aesthetic panel and fix it with 8 screws L. Fig. 6

e. Remount the door on the hood, first on upper guides M1, then on the lower M2. Fig. 6

f. Close completely and re-open the door to check its correct sliding on the guides.

Installation

a. Use perforation diagram N2 (*). Position the diagram on the front edges of the wall unit

(right wall unit, B side) – (left wall unit, C side) WITHOUT CONSIDERING THE

THICKNESS OF THE DOORS, and make the holes as indicated. Fig. 8

b. If necessary, fix the hood to the wall, putting template N1 (*) on the wall so its upper edge

coincides with the upper edge of template N2 (*). Fig. 7-8

c. Make the holes as indicated. Fix 2 hooks (*) R to the wall with screws and dowels. Fig. 7

d. In case the thickness of the lateral wall units is 16mm, put, with embedded fixing, the O (*)

spacers at the sides of the hood in correspondence with the holes used for the passage of the

fixing screws to the lateral wall units. Fig. 8.

e. Hang the hood onto the hooks (*) and adjust the position of the hood with headless screws

S1 and adjusting the position of the hooking brackets with screws S2. Fig. 7

f. Fix the hood to the lateral wall units with 4 screws P. Fig. 8

g. Mount the lower corner Q (*) to the hood with two screws and plastic washers T. They

will serve to cover possible spaces between the rear of the hood and the wall. Fig. 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baumatic bt06 6me Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info