Bedienungsanleitung Baumatic bt18 5 (Seite 3 von 6) (Englisch)

332003

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

14 15

by 50°C.

Before connecting to the power mains make sure:

• The mains voltage corresponds to the rating of the unit (see rating

plate).

• The modulating valve and domestic wiring can withstand the charge

of the appliance (see rating plate)

• The outlet or omni pole switch used for connection are readily acces-

sible to the appliance installed.

Our cooker hobs comply with EEC Directive 89/336 on the prevention

and elimination of radio interference.

Appliances must always be grounded. Our company is not responsible

for failure of the grounding system to function and for connections that

do not comply with the provisions of the laws in effect.

NATIONAL REFERENCE STANDARDS

Connection to gas supply, gas connection and ventilation of rooms must

be carried out in accordance with local regulations.

REGULATION OF MINIMUM

Our taps are suitable for all types of gas and are regulated at the mini-

mum as follows:

1.Light the burner and turn the knob to the minimum position. If the

flame should go out, proceed as follows:

a) light the burner at maximum capacity (large flame)

b) remove the knob

c) introduce a small screwdriver in hole B on the shaft of the tap (pict.

6) and unscrew the adjustment screw by two turns. On some units

hole B is on the right or left of the tap (pict. 6/B and pict. 6/C).

NOTE: on some units, to access regulation hole B it may be necessary

to unscrew lock ring C (pict. 6/C). Depending on the type, the minimum

adjustment screw may be on the right or left of the tap.

d) replace the knob and turn to the minimum position (small flame)

e) remove the knob and proceed as in 3.

2. Remove the knob from the tap

3. Introduce a small screwdriver in hole B (pict. 6) and tighten or loo-

sen the adjustment screw (taking care not to turn the shaft of the

tap) until the burner flame is properly adjusted at the minimum.

The gas supply is correct when the tip of the flame reaches a length of

~ 4 mm at the minimum.

Check that when passing quickly from the maximum position to the

minimum the flame does not go out.

REPLACEMENT OF NOZZLES

The burners are adaptable to different types of gas by replacing only the

nozzles for the type of gas used (see data table). To access the nozzle,

simply remove the cap and flame-breaker.

To change the nozzles, use a no. 7 socket wrench (pict. 7).

IMPORTANT!!!

In case of appliances installed previously, always disconnect the power

before performing any operation.

(pict. 6/B)

(pict. 6)

(pict. 6/C)

(pict. 6/A)

(pict. 7)

Nozzle

(pict. 8)

(pict. 9)

(pict. 9A)

GAS COOKER HOBS

RECOMMENDATIONS FOR ENERGY SAVINGS

Use of cooker hobs

The cooker hob is composed of burners of different diameters. To use

the gas in the most economical way, use the burner best suited to the

dimensions of the pot (see fig. 8); when it reaches the boiling point turn

the flame down to the minimum.

Always use pots with lids.

STEAK BROILER (optional)

If you have purchased a cast iron or iron broiler plate it is best to use

the medium or low burners to heat it. If you have to use one of the large

burners for any special reason, turn the flame to the minimum (small

flame).

TURNING ON AND ADJUSTING THE GAS BURNERS

The mask next to the knob shows the settings in addition to indicating

which burner is used. The symbols are as follows (fig. 9):

Full disk • Off

Large flame ∆ Maximum level

Small flame ∆ Minimum level

ELECTRIC IGNITION FOR GAS BURNERS

Ingnition with separate button: Turn the knob corresponding to the bur-

ner you want to light to the maximum level (large flame).

Press the knob down and at the same time press button A (fig. 9/A).

Under-knob ingnition: On some models the electric ignition is operated

directly by the knob. To light the burner turn the knob to the maximum

level (large flame) and press. If the burner does not light instantly, turn

it to the minimum level (small flame) and repeat the operation.

GENERAL CLEANING AND MAINTENANCE

TAPS

The taps do not generally require any maintenance. If they become hard

to turn, replace them.

Note: this should only be done by specialized personnel.

CHROME-PLATED GRIDS

Some color change due to the heat of the burner is inevitable.

To attenuate it, clean the zone with a sponge and abrasive powder.

PARTS IN STAINLESS STEEL

Clean the parts with soap and water then dry with a soft cloth.

Use special cleansers for stainless steel periodically for maintenance.

FOR THE USER

Burner ø of pot in cm

Large (rapid) from ø 21 to ø 26

Medium (semirapid) from ø 15 to ø 20

Small (auxiliary) from ø 6 to ø 14

Triple crown from ø 24 to ø 30

Ultrarapid from ø 24 to ø 30

Fish-burner oval pot

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baumatic bt18 5 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info