Bedienungsanleitung Baumatic segreto (Seite 16 von 19) (Englisch)

129297

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Instruction on mounting and use

Consult the designs in the front pages referenced in the text

by alphabet letters.

Closely follow the instructions set out in this manual. All

responsibility, for any eventual inconveniences, damages or

fires caused by not complying with the instructions in this

manual, is declined.

Use

The hood has been made for use in the internal recirculating

filtering version.

Cooking fumes and steam are aspirated inside the hood,

filtered and cleaned, passing through the fat filter/s and the

carbon filter/s that MUST be supplied with the hood.

Attention!

If the hood is not supplied with carbon filter, then it must

be ordered and mounted.

Installation

Specialised personnel must carry out both the electrical

and the mechanical installation.

The minimum distance between the supporting surface for the

cooking vessels on the hob and the lowest part of the range

hood must be not less than 50cm from electric cookers and

70cm from gas or mixed cookers.If the instructions for

installation for the gas hob specify a greater distance, this

must be adhered to.

Electrical connection

The mains tension must correspond to the tension shown on

the characteristic label situated inside the hood.

The product is meant for connecting directly to the mains

supply, therefore apply a regulation bipolar switch that

ensures complete disconnection from the mains in the

conditions of category III over-tension, conforming to the

installation rules.

ATTENTION! Detail B (fixing bracket to the ceiling - Fig. 1)

is equipped with a conductor (yellow-green) that must be

connected to the earth of the domestic electrical plant.

Fig. 4

ATTENTION! Be particularly careful about positioning the

excess cable. Failure to observe this indication could cause

grave damage to the apparatus and/or an electric shock to the

user or the installer. For further details see Fig. 6-22

Attention! Changing the interconnection cable must be

carried out by the authorised technical assistance service.

Mounting

Expansion wall plugs are provided to secure the hood to

most types of walls/ceilings. However, a qualified technician

must verify suitability of the materials in accordance with the

type of wall/ceiling. The wall/ceiling must be strong enough to

take the weight of the hood. Do not tile, grout or silicone

this appliance to the wall. Surface mounting only.

Description of the hood

Fig. 1

K. Control lever

Attention! The control lever is already supplied. It is to

be installed last, before connecting the hood to the

mains.

Insert the control lever into the apposite housing (see

drawings on the first pages of this booklet - triggered

connection, compulsory direction.

L. Halogen bulb

M. Lateral filter holder frame

N. Active carbon filter

O. Metal anti-fat filter

Note: other carbon and anti-fat filters are installed inside

the hood in correspondence with the shaped lateral slots

and the upper part of the hood.

P. Anti-fat and carbon filters holder frame

Q. Filter holder frame releases

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

The hood is equipped with a “TOUCH SENSOR” device able

to determine the control of the lights and the speed when the

user touches the control bar. Read the instructions below

carefully for this purpose.

Automatic switch-on function

The hood is equipped with a temperature sensor that starts

the motor at the 1st suction speed (power) when the room

temperature around the hood is higher than 70°C.

The user can, however, switch off or modify the suction speed

(power). (See paragraph “Control of suction speed (power))”.

Control of suction speed (power)

The selection of the suction speed (power) is cyclical,

according to the speed sequences “”stand-by - 1-2-3-4- Stand

by -1-2-”… so that at every touch of the UPPER PART of the

control bar the suction speed (power) increases by a level

and then to switches off (stand-by) if the control bar is touched

again when the hood is at suction speed (power) 4.

It is possible lo turn the hood off (standby) even when the

hood is at any speed by pressing the UPPER PART of the

control bar (for more than 3 seconds).

It is possible to determine what suction speed (power) the

hood is in when the bar is equipped with a led that changes

colour on the basis of the suction speed (power), as follows:

Hood in stand-by: LED OFF

1st suction speed (power) - led GREEN

2st suction speed (power) - led ORANGE (amber)

3st suction speed (power) - led RED

4st suction speed (power) - led RED (FLASHING)

Note: the 4th suction speed (power) remains on for 5 minutes,

after which the suction motor switches off (Stand-by)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Baumatic segreto Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info